Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Dear all,
I'm not able yet to start advertising with whitelist whith this code:
void AdvInit(void)
{
ble_advdata_t advdata;
uint8_t flags = BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED;...
I have a nRF51 DK board and its flashed with the SD 110
I want to have a timer which will interrupt every 50us.
This is how I set up the timer:
#define APP_TIMER_PRESCALER...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hi
I'm using nrf51422 to send periodically a frame through ble_nus service to the Nordic nRF UART app. One of the frame data is the message count number, that is reset...
Hi,
I would like to install Master Control Panel on my PC.
Where can i find the installer for a windows desktop machine?
Also is there a user guide available for...
Hello,
I am currently working on a project that is using the nRF51422 chipset (Rev 2 silicon) and the S310 SoftDevice Version 1.0.0 and I am having some problems with the...
Hi all,
I have an PCA10001 board and a custom PCB which also uses the QFAA version (256KB flash, 16KB RAM). I'm trying to enable OTA feature for our custom board. I use the...
Hi,
i am having trouble to understand and use flash to store data. First of all as far as i understand ble_flash is obsolete and replaced by the pstorage module, correct...
Hello,
I was reading about RF design and some articles say that if the transmission line is short enough, you may not consider impedance-control as the effect is not visible...
Hi all,
For my project I power the nRF51 DK from a supercap using an external LDO(3.3V) connected to VDD. This way I can keep the board powered using the supercap. I also...
Hi
I'm using PCA10028. it has nrf51422 with softdevice s110. For getting printf in console I'm using 'app_uart.c with FIFO' and 'retarget.c'. When i try to print something...
