Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello all,
I have below queries on my custom board and mesh.
I have designed my custom board using nRF51824 and i am using J link debugger for programming , I can able...
Hi, I know there are already lots of threads around this but it seems none is like mine.
I'm running my toolchain on a Mac so I think I have a more challenging debug setup...
Hi,
I would like to know is there any shopping sites selling beacon modules that we can configure later based on our requirement?
I searched on few shopping sites where...
Hi,
We are developing a pretty complicated multi-threaded application on nRF52832.
Part of the requirements are storing a large amount of data over time (Megabytes)...
Hi
I am using gpio for input interrupt as below
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_HITOLO(true);
in_config.pull = NRF_GPIO_PIN_PULLUP;
...
According to PS, external reference min. voltage is 0.83V. However, I've experimented with voltages of about 0.2V and it appears to work. Specifically, I connected a voltage...
Dear all,
I am planning to develop a system which has the same functionality as N550M8CC SoC.
I cannot use directly N550M8CC module because space limitations so I am...
Hello everyone
I am trying to write to SDCARD with FATFS.
Data received from BLE and SAADC incoming data.
Writes every second.
The size is about 100 bytes.
SAADC is 1000...
Hi guys,
I wanted to try out the experimental "ble_app_att_mtu_throughput" on the newest nRF5240 DK. Using Keil, this project is to big for the free version. Since I knew...
Hi everyone,
I have one problem with the application timer. When I change the state of characteristic to the value of 1, the following code is executed:
err_code = app_timer_stop...
Just stumbled upon a few questions, which are hard for me to answer at the moment.
I wanted to do some throughput measurements with the example taken from SDK 14.2.0 mentioned...
What does the QSPI controller inside the nRF52840 do when the ACTIVATE task is started?
Does the ACTIVATE task result in communications with the external QSPI part such...
Hi,
I have a question about the UARTE peripheral.
is it possible to keep the DMA running and let it write to ram in a circular way?
I used DMA on the stm32 before and...
