Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hello,
I would like to know the best practices to update a passkey for bonding.
For the moment, I have a static passkey that I set during ble initialization and I can...
To start off here, I'm using a Laird DVK-BL652-1.0, which according to Laird only needs to be re-configured to use the internal oscillator, but is otherwise very similar to...
Folks,
Have been using Keil MDK Lite in the past, in a Win VM. Larger code (over 32KB) plus the convenience of running without a VM layer have led me to switch to NetBeans...
Hi,
I want to use the AES-CCM of nRF52832. But it can not work with the softdivice.
I have read the following question and answer.
devzone.nordicsemi.com/.../
It seems...
Hi Nordic folks,
We are developing a product using nRF52832 with a Power Amplifier (RFX2401C) for extended range. For communication we are using ESB with some modifications...
I was redefining the init packet and when it came time to generate the nano-pb files, it looks like there is a fair amount of difference in the newly auto generated pb.c and...
Sorry if these questions are discussed already. I'm a newbie to Bluetooth project. Let me explain in brief. I have a central and peripheral device. I am transmitting 10samples...
After quite a few difficulties getting Keilv5 to work with the included examples with no responses ( devzone.nordicsemi.com/.../) I decided to give Eclipse a shot.
This...
Good day All,
We are in the process off procuring a project using nRF52, and I need to find out some important things. Are there any costs in using any of the libraries...
I am using nrf52840 module(peripheral) for transmitting 10samples/10ms and central device as the same nrf52840 for receiving the samples. Although I receive the packets, there...
Hello,
I'm working on an application in which I have to dynamically switch between a TWI master peripheral and SPI master peripheral that use the same peripheral ID (our...
I have an NRF24LE1 transmitter using ESB. It is sending a static payload of 10 bytes every sec.
The other configurations on the transmitter are: RF channel:2, CRC: 1 byte...
Hi,
i'm wondering if there is any IC (for example nRF52832) that can reach a range up to 155 meters available within the Nordic semiconductor catalog ?
i know that the...
In nRF5 SDK 12.1.0 a bug was fixed in nrf_drv_wdt_init(). Watchdog timeout could not be larger than 131 seconds because of (x * 32768) multiplication before. This bug is again...
In the spec it says that the typical ramp up time is 140us (or 40us in fast mode). But there is no details on maximum or minimum. What is the true tolerance on this value...
