Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hi,
I am using the nRF6310 + PCA10005 +nRFgo Studio as the lower tester, the supplied python scripts as the upper tester, and my own custom board as the DUT.
I've looked...
Hello, I am working with nrf51822 on my pcb design by myself, I read temperature from chip, the result is about 90deg, (I have div by 4 for 0.25 deg) it is impossible for...
Is there a way I can tell which version of the chip I'll get from a distributor? It's not clear to me that I can tell, from, eg the Mouser product page which rev it is. Is...
Hi,
I am working on proximity android application, i implemented immediate alert service, which is working fine. Now i need to set the alert level on the tag for linkloss...
Hi
I am working with alert notification example. I just wanted to know how you have tested the alert notification client example implementation. Is it just by using the...
Section 28.9.9 of the nrf51 reference manual shows the Config register has 3 defined bits, BBA. A is for Hardware Flow Control and is one bit, 0 or 1, which makes sense. ...
Hi,
I'm trying to add more user services to LBS demo. I generated 128b UUIDs for my services. Then I should add them to list returned by scan response in function advertising_init...
Hello!
Sorry for a new guy's description.
We had a device running in normal firmware application mode, and the Bootloader was programed. It's our goal to accomplish DFU...
Hello
I am using the nRF8002 kit. I would like to inform the host (Android app) when there is a long button press on the input pin.
Is this possible and if so which BLE...
Hi folks,
I was wondering if someone has a reference implementation of a bootloader that uses exclusively ANT technology to make DFUs, being it ANT-FS or any other alternative...
Dear Nordic guy,I'm developing with nrf51822 (6.0 stack binary and 5.0 SDK).
I recently updated the code and stack binary(6.0 stack binary and 5.0 SDK).
My function is not...
This is something for the legal department.
You had some questions here about the RFduino before. This question is about legal obligations Nordic supposedly imposed on...
Is it possible to use an nRF8001 without a separate microcontroller to advertise non-connectable advertising packets specifically containing battery level information only...
I take the nRF UART 2.0 for reference. I make the nrf51822 be always sending packages ,and if it sends one package succussfully,and the smartphone just shows what it receives...
Hi guys,
Is there any way that I can re program the MAC ID of the nRF51822 devices through the SWD interface? I was able to do this using the UART interface with the BL600...
