Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
I’m having some troubles with example code : ble_app_uart_s132_pca10040. The code compile well in Keil and I can prog it in the nfr52 but it doesn’t run. When I check...
To enable comparability with an existing client, I'm attempting to configure the nRF51822 to provide a GAP service that includes user description descriptors (UUID 0x2901...
I'm trying to store some values with fstorage. The store operations seem to be queued successfully, but never executed. I currently have this to test the behavior:
FS_REGISTER_CFG...
Hallo everyone,
I am reciving a notification from my server, which lenght can be 8, 20, 30 bytes but when I want to display the info using NRF_LOG_INFO is not printing...
To All,
From reading the datasheet I understand that nfr52832 spi can only send/receive up to 255 bytes at once. And to work around this a list method is used.
Because...
Hi,
I’m working on a device that requires to enable the softdevice when connecting with a smartphone via Bluetooth and disable it when acquiring data from an analog source...
Hello,
I am using sdk12 and uart code. I want to send my sensor data readings to ble app. For that I have modified the ble_app_uart code and I am able to send 8 packets of...
Hi all,
In my project I have a structure its length was about 2KB, I'm saving it as a static variable after using this I come across with a weird behavior from the board...
Greetings,
I'm having trouble being able to perform a DFU with the secure serial DFU. My setup:
Using PCA10040 (nRF52832) with the s132_nrf52_4.0.2_softdevice.hex...
Hi.
I am using saadc sample cod of SDK13. Changing some parameters based on the analog input, the example is sucking somewhere where I have not been able to find it.
...
Dear all,
I am facing small problems, which I guess most of you faced at some moment.
I am trying to switch from working with ST microcontrollers to working with nRF52...
Hi,
I know that the default handle value of device name is 3, but in my application i am not getting the default device name handle, is it possible to change the device...
I want to save precious CPU cycles by writing 40 i2c (TWI) registers in one shot. Can I somehow set up the TWI master to write 40 registers (each 16-byte address with 8-bit...
What is the maximum length of pdu for ble advertisement? I have ported the example application of solar powered beacon without softdevice.
I just wanted to know if it was...
