Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hello,
We are using Nordic SDK 11 MQTT adapted for TCP/IPv4(separate module) . It works fine without TLS. I added the flag "MQTT_TRANSPORT_SECURE" and made adaptations...
Hello,
Question regarding using the SPI master peripheral with DMA to communicate from the nRF52832 to the ads1296 device .
In order to use this device in the mode and...
Hi engineers, Here we are facing a critical problem in which the NRF51822 stops handling/processing the GPIOTE->PORT interrupts after some days good working. This problem...
I have a project which needs to be built in IAR, but uses the signed bootloader. I understand, that if I want to flash and debug the application from within IAR, I need to...
Hello,
In my next project I plan to conductive pads as buttons(that are exposed for humen touch to interacte with the) one is connected to ground and the rest will connect...
Hi,
I am using SDK v14.1 for nRF52840.
The secure_dfu_usb debug example works well when the J-link RTT Viewer is connected.
But when the RTT Viewer is disconnected the...
Hi everyone,
I would like to know if it is possible to establish a serial communication to a PCA10028 card using Adafruit Bluefruilt LE friend knowing that there is no...
Hello everyone,
I am using nrf51822 chip that has functionality to flash bl, sd or app using mobile app application. I want to reuse this functionality in order to have...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
I am using the ble_app_uart example as my base on a 52832 with sdk 12. My project runs off line power and needs to remain available for connection 24/7. I have commented out...
I am communicating with a temperature sensor (MLX90614), which has flag register. However, in order to read this register, I must send a read sequence without issuing the...
Hi,
As has been mentioned many times, the DIF on both the nRF51 and nRF52 consumes quite a bit of current. In the past, on the nRF51, I've relied on power cycling both chipsets...
Hello,
I would like to make changes in ble_app_uart_c example for connecting to a custom peripheral.
Service Uuid of my peripheral is as follows : 99aa0001-d0e3-44ce-a306...
Our homeowners association has a gate which opens when a transmitter in the car is pushed. I would like to add a BLE device to the gate which would trigger the gate to open...
Hello all,
So.... i'm quite green to the Nordic and Bluetooth protocol.
i want to program NRF51422.
what i have now it the Nordic test board and a spi-canbus print. this...
