Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello,
I want to use NORDIC nrf52 to perform some power consumption Analysis. Is there any eveloution board from NORDIC that don,t have debugger connected to it? I want...
Hi all,
Is there a tutorial that explain better the bonding information and whitelist? I have more doubt about that.
My first code i have pairing and bonding:
...
hello..
I'm actually working on nrf51822,i could complete the advertising part successfully("hello world")..NOW i want to add privacy feature which allows an advertiser to...
Hi there,
I am working on the SDK13 project template that I am modifying in order to install a vendor type uuid.
But my code crash on "advertising_init" and ble_advertising_init...
While using the secure bootloader image and test application works consistently using the development kit I have not been able to port the solution reliably for our custom...
hai
i am using mbed to program my nrf51822.i want to set the analog pin p6 as analog in in one situation and as a digital out in another situation. but i am unable to do...
Hello.
After executing the code below, the RAM was dropped and the program could not be written.
for(idx = 0; idx < 7; idx++)
{
NRF_POWER->RAM[idx].POWER = (POWER_RAM_POWER_S0POWER_Off...
I'm studing the project of ble_app_gls/PCA10040/SDK11.0/ ,I have got some questions about the RACP indication pending and retransmittion mechnism. In this project(File ble_gls...
enter code here Hi guys I have managed to program an example BLE_Serial program into the nrf51822 but I cannot see anything coming out from the TX and RX ? Please guide me...
I've tried to install nRF Connect v2.0 on both Win 7 and Win 10 systems, both running Avast Anti-virus (up to date). In both cases the antivirus gives a warning about IDP...
I have the Memory Manager module enabled in my custom sdk_config. Within the module, I have both of the following defined.
MEM_MANAGER_ENABLE_LOGS 0
ENABLE_DEBUG_LOG_SUPPORT...
Hello - Is the long range option programmable in BT 5.0? During the run time, is it possible to switch between high speed and long range mode dynamically depending on the...
I am specific about master as I have to connect two simultaneously(obviously to two different pins pair). Plz provide any code outline if you have, Thank you in Advance
Hi.
I would like upload firmware from Atmel microcontroller to nRF51822 with SD130.
I suppose that I have to use single_bank_serial_s130 in nRF51822AA, but what I have to...
