Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm using S110 version 7.1.0, but need a way to validate in general which S110 and which SDK version I have associated with this .uvprojx project.
Much of this stems from...
I'm running the ble_app_beacon_s110_pca10028 example on my NRF51 dongle. The good news is that I see a beacon transmission on my iPhone 6 on this "Pally BLE Scanner" app....
We are developing a new BLE tag product using the nRF51822. We would like to assemble the PCB and battery in a single operation then program the product sometime later. Can...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
I'm trying to use RTT for debug printing and having some trouble. I'm using the nrf51-ble-app-lbs example app that goes with App Note 36. I've added the RTT code from www...
Hi,
iOS device uses random private resolvable type changes own bluetooth address address every 15 minutes as long as I know. Can I see the transittion just to change the...
I see the python S110 bindings (via SWIG) have been made; it was pretty easy to get the demo code up and running, many thanks! Any chance that S120 central role bindings can...
I have a custom board with an nrf51822 device. I also have Keil 5.12 and a ULINK2 and would like to program softdevice hex file into the nrf device. I have followed all of...
I'm trying my best to get started w/ the nrfgo 51822 development kit that I got last summer, but I'm just having a hard time jumping in.
I was a little disappointed to...
I need to use a high speed PWM (> 500 kHz) in which I can vary the pulse width. In examples, it's handled in software which is too slow.
Is there any way to set a pin on...
Hi,
I am having some problems getting the s110 SoftDevice working (sd_softdevice_enable stops the program execution) on a custom PCB. I have seen several issues similar...
Hello,
I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated...
I'm interested in getting started with NRF51, but the full DK is quite expensive here and I don't need it. Does the nRF51-Dongle sku come with a key for downloading & using...
Hi,
Can someone tell me (definitively) what the max SPI clock speed is?
I have seen 2,4 and 8Mhz here and in recent documentation and I'm confused.
Thanks
