Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I have a thread using a Timer and PPI to trigger SAADC sampling at 100hz. Currently I have an app_timer also running at 100hz to sample the results of the SAADC (and its time...
Hi guys,
I notice that the bytes array of UUID is reversed after registerd.
For example, I define the UUID marco as follows and registe it at ble_nus_init().
#define...
I am trying to use ESB and BLE concurrently on NRF51822 SDK v11 SD130..
The BLE part is working fine but the ESB part keep causing error randomly.
I put a break-point in...
when i use C:\Users\Administrator\Desktop\nRF5_sdk14.0.0_ble_central_beacon\examples\ble_central\ble_app_multilink_central for this instance ,I debug the discover moudle callback...
The question I mentioned here
When using ble_gatts_hvx to send data, only send data pointer and length to softdevice, and softdevice did not copy these data to the softdevice...
i used pca10040_debug of bootloader_secure of nRF5_SDK_14.1.0_1dda907.
i created the key by myself.
Bootloader and zip file used the same key.
My device is in DfuTarg...
I'm using an NRF51 w/ S130 operated directly from a coin cell battery. I use the ADC with a voltage divider to successfully measure analog voltages. One of the challenges...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
NRF52832 reference design BOM did not specify the voltage rating of capacitors. What is the recommended voltage rating of capacitors?
For 32 MHz Crystal Oscillator, specified...
I'm trying to use the TWI talking to a I2C device (LED driver TLC59116). I have some working arduino code which I have converted to use on my nRF52 custom board. I'm using...
Hello,
I'm trying to measure battery voltage on nRF52832 chip using SAADC based on examples/peripheral/saadc and examples/ble_peripheral/ble_app_proximity and noticed that...
Hello Community,
I have a peripheral device which is transmitting the data through custom battery, accelerometer and temperature services.
Now I need to receive that...
Hi everybody !!
i m working in a project with NRF52 SDK 11, i need a help, i want to create a funtion that working with RTC to count a tick and to convert it into time then...
Hi ,
I want to create a periodic task which has to run every 10 seconds, how can I create such a task?should I use threads for it? And which clock source does the task...
