Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi Team,
I would like to implement a second bootloader to program an external serial Flash chip.
Currently using S110 V7.1.
My current thinking is to create another...
Hello--
I have an NRF51422-DK devkit (PCA10028, v1.1.0) and noticed that pin P0.31 is not brought out to the connectors or mentioned anywhere in the nRF51-DK-HW schematic...
hi all
nRF24L01+ ???
as the data sheet wrote the support life :These products are not designed for use in life support appliances
what is mean this sentence ???
does that...
When I try to make a custom service with the S110, how do I set the service and characteristics up to use a custom 128-bit UUID instead of a 16-bit one, based on the Bluetooth...
hi Guys pls HELPPPPP
I have developing active rfID tag using nrf24L01+ and ATtinny13A, the program code is done perfectly, firstly I start developing the tag with separate...
Issue is related to:
devzone.nordicsemi.com/.../
Now I use latest SD S130_1.0
So, I added to my service characteristic with notifications enabled. But during discovering...
Hello,
I have a development kit with the PCA10000 and I can comunicate with the PCA10004 for about 5/6 meters what is ok for my application but now I want to comunicate...
Recently I needed to add some functionality, so the software could monitor when there was a ble gatt read characteristic event.
In the addCharacteristic code I simply set...
Hi, We have used nRF51 DK for developing an application where we used USB to load/flash the program code. Now we are in Pre-production stage where we can use only the nRF51422...
Hi,
I would like to extend the HTS service with measurement interval setting support. Bluetooth SIG specifies the measurement interval characteristic, which is easy to...
I'm using the example ble_app_hrs along with the HRM part of the nRF Toolbox iOS app . It makes sense to handle this in on_ble_evt in main.c but am unclear how I can recover...
Hi Team,
I am testing UART on nRF51 DK kit.
I have flashed uart_pca10028 .
I have taken out jumpers from P0.9(TX), P0.11(RX) and GND and connected to PC com port.
...
I have the example app working nicely now, so I want to export the project to a zip or something, effectively copy it, and put it elsewhere in my filesystem and work with...
Hi,
I tried installing the kernel (raspbian-kernel-zip Raspbian kernel for Raspberry Pi 3.17.4 ) on a Raspberry Pi 2 (Model B 1 GB). I found out that the Pi doesn't boot...
