I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Hi,
The URL below does not have the DNs number for v2.9.2, but is it the same as for v2.9.0 and v2.9.1?
https://docs.nordicsemi.com/bundle/comp_matrix_nrf54l15/page/COMP...
Dear Nordic Semiconductor Team and Community Members,
I am currently working on an nRF54L05 project where I aim to use only the primary slot in MCUboot due to memory constraints...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi
It seems that the default minium DTLS handshake timeout is about 1 second. That means, there is a retransmission if a response isn't received within this timeout. In...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Background : To set up a Matter ICD (Internet Connectivity Device) and Thread as a SSD (Sleepy End Device). Here are the detailed settings：
Currently, the Matter over...
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
We are currently working on a custom modem firmware update. For this, we would like to use the CBO file you provided. Updating the segments with the CBO file is working so...
Hi,
I'm half way through the Cellular course on the dev academy and although I am able to connect to the Nordic and Hivemq publich brokers, when I attempt to connect to...
Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
