According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I want to request AGNSS information from nrf cloud services using my nRF9151DK board. As a first step, I flashed the nRF Cloud multi-service application onto my DK...
Hello,
I just received my Thingy:91X which I purchased through DigiKey. I am trying to connect it to hello.nrfcloud but I keep getting the following message: " The fingerprint...
I am using Segger Embedded Studio and the nrf52840 development kit.
I can run the BLE peripheral examples using SDK 15 and s140 V6 "blinky" and " cscs" .
but the ble_app_rscs_pca10056_s140...
Checking if this is possible and how to complete.
For the ble_app_beacon example, I'm able to reuse #define APP_DEVICE_TYPE 0x02, to be #define APP_DEVICE_TYPE 0x0E, 0x06...
Hello ,
we are new to BLE
1. We make a long life temp and light sensor , just only transmit from the Nrf to mobile (one way ) , we would like :
1.1 sensor always be...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
Hello,
For my project, I want to be notified when my device changes the value of my characteristic so i used the HealthThermoDemo example.
here is my code :
But despite...
Hi , I want to use two GPIO oin with button press hadler even . when pin low will interrupt and into handle..
Below is the code for the single key.
Thanks.
Pa...
This is somewhat of a continuation of this topic:
What does APP_BLE_CONN_CFG_TAG do?
Softdevice 132, header: ble.h: SVCALL(SD_BLE_CFG_SET, uint32_t, sd_ble_cfg_set(uint32_t...
I'm using RFduino that utilizes nRF51822. I need to set a timer1 as timer0 is used by the BLE stack, so I used the following code:
#define TRIGGER_INTERVAL 1000 // ms...
Hello,
Today I had a case where I tried to perform a bootloader-only DFU on a device with a debug version of the bootloader, but instead of trying to replace it with another...
Hi Technical team,
I want to use nrf52832 for my project, below are the some doubts i have with nrf52832
1) nrf52832 will act as HUB and receive data from peripheral...
Hi,
I have already working code in nordic sdk 13.1 with eclipse. But we are move to latest sdk v 15.0 for example of central and peripheral. Now every thing i have modified...
After a node successfully provisioned in the Mesh Network. If I want to unprovision the node, what procedure is needed to make it?
Should I remove all the netkey, appkey...
Hi, I have a problem with the usb HID examples in sdk v15.0 on a nrf52840 Preview DK. I cannot get them working together with a Linux or WindowsCE based USB Host, with Windows10...
Hello.
I'm modifying the Eddystone Beacon Application example. For now, I can transmit my own Eddystone frame. This frame is static, and the board starts transmitting it...
