Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
I'm trying to run the ble app uart central example using SDK15 with Embedded Studio.
When building the project, I encountered an error in retarget.c, where the error...
Hi,
I have a couple of WT51822-S4AT boards I would like to use to send data from a PC to one board via UART and then pass the data to a microcontroller connected to the...
Hello, i'm trying to store data in the flash, i manage to write a correct data in the flash but when i try to read it the address is erased.
I use this function to write...
Hello, everyone~
I want to use a nRF51824 to scan a specified smart phone and use the RSSI to estimate the distance. Is there a simple and basic example of this funtion...
Hello everyone
I have a small question about Mesh_gatt_pdu_type_t in light_switch_example.
When my NRF52 connect with smartphone over BLE mesh proxy, my smartphone will...
I am developing my project in a nRF52832 custom board. I am working in SDK v12.2.0. My application program is based on ble_app_uart.
It seem a bug about the defined characteristic...
Hello All,
I have compiled and flashed fresh ble_sdk_app_proximity with armgcc to my NRF52DK(S132,SDK15.0.0). After connecting to the DK with nRF connect ios app I can see...
Hi All,
Am using SDK 11.0.0.89a8197 Device Manager,
I get this error very randomly .. My case is I allow only one device to bond with me , After bond I always advertise...
This question is similar to the feature request: devzone.nordicsemi.com/.../sdk-12-x-0-future-feature-requests
I have to evaluate if we buy Tracealyzer ( percepio.com/....
Hi.
I have a problem to understand what is the difference in SFR registers IEN1 and INTEXP.
Bit 2 in both of them is responsible for enabling 2-Wire completed interrupt...
Hi,
We are currently developing an app which require DFU.
As part of the bootloader development we would like to use the SWO in order to do a printf debug.
In the app...
Hi there,
I am looking to double check the state of NRF52840 while its reset is active.
I have found this thread regarding the NRF52832 ( https://devzone.nordicsemi...
Hi,
I am using sdk12.2.2 and customised nrf52 boards. I am storing 9000 records with 7 bytes each in flash.
After sometime I am getting buffer space full error and I am...
Hi!
I am developing anapplication on NRF52 DK. I need to preserve value between software resets and to do so i tried to use GPREG .
To set value i use code:
//set value...