Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hello,
I'm currently using Visual Studio Code with the newest SDK, Toolchain and Plugin on MacOS and most of my applications are freestanding applications.
Now I want...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Are the PCB antennas provided in eagle library of NRF52810 ( github ) require any additional components for impedance matching or i can directly add the PCB antenna to ANT...
I downloaded radio_test.c from Nordic and complied it to output a .hex file. Now I want to flash this .hex file onto nRF52832. Does it require to softdevice and bootloader...
Hello (I'm new to this nRF-world...).
I am searching for a small "nRF-52832 clock" (arm mounted watch) that at least reports the "surrounding/room temperature" (not only...
Hello
SDK12.3, nRF51822
Example Gazelle from SDK works fine. If I use the softdevice (add ble_stack_init) then the program freezes in the nrf_gzll_enable
I want to do changes for firmware upgrade nrf52832 with SDK BLE_2.0.1 for the mesh.
I need DFU (Bootloader)UART for our application to upgrade nrf52832 firmware by the host...
Hi
I have written this code based on a sample from SDK12. The board is a pca10040 and nRF52832 chip. It seems like after disconnection from the master device the Softdevice...
Dear support team,
Channel survey (RSSI report for each data channels) are now available on S132v6. However, for users who need to use v4.0.2, is there alternative method...
I am using the Hackable Kit from Electronut labs and using their Bumpy , black magic probe alternative for programming. I would like to control a servo motor precisely at...
My code is on the multi-link example and it works well when I use another nrf52dk board as the "Nordic_Blinky" peripheral device, but it can't find my other BLE device.
...
Hello
I am running gls example on SDK14.2.
I paired after flashing program to my DK board, and then turn off power.
And turned on again, but i can't connect to my DK...
HI. I used a translator.
I am using the RNG example of SKD15.
I know that when I set the range of the random number to 1 byte, the number from 0 to 255 is generated. ...
I am using a Raspberry PI as a 6LoWPAN router, running Raspbian 9.4. Linux 4.14.34. Radvd 2.15.
I configured everything as described in IoT User Guide . I am using Miredo...
Hi,
As well know, the nrf51822 can only work either TX or RX mode at the same time.
Normally, the nrf51822 device is working in RX mode (by using function "nrf_esb_start_rx...
Hello, i'm trying to updade my firmaware using the DFU. I manage to do it with nRF Connect and nrfutil but i'm trying to a custom central to flash the software without any...
Dear all,
I am using an adafruit-nrf52-pro-feather (nrf52832) to run my project of detecting voice by this below scenario:
++ Setting up:
[PC] ==== USB cable ====...
