Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello,
I want to connect some ammount of central devices to one peripheral.
nRF52840 or nRF52832 considering as peripheral. Latest SDK (15.0.0) will be used.
Connection...
Hi there,
I'm about to develop my first BLE product and got my eyes on the nRF52840.
My product should be able to do the following:
1. Continuously read high rate data...
Hi All
I'm trying to measure the Ton and the Toff of a signal present on an input pin of a nRF51822.
The idea is to use PPI, Timer 1 and save timer on every falling/rising...
Hi,
we are using Linux machine and my application is running init, blue tooth stack is running on nrf52 board but after initiating the scan command we are not getting continuous...
Hi all,
I am using a linux based board and wanted to support BLE5.0 on that board. PCA10040 is connected with My board through UART. Please forgive me for these basic doubts...
Hi All,
Moto E4 mobile phones do not connect right away and at times takes few minutes and connects eventually. Right after I hit connect I get an error 0x85(GATT ERROR...
I am using Thingy (nrf52832) to advertise Eddystone UID and TLM packets in bursts. On a given event advertising starts with an interval of 200ms, then stops after specified...
My SPIM0 starts to use 300uA upon first usage of nrf_drv_spi_transfer. Why? Even when the transfer finishes and I uninitialize SPI or turn the MOSI, MISO and CLK pins to the...
Hi there ..
I have question regarding estimation of a coin cell battery life while advertising on nrf52840 PDK. I followed here https://devzone.nordicsemi.com/b/blog/posts...
Hello,
I am fairly new to developing ble beacon applications and was wondering if it was possible for my device to perform the following operations simultaneously:
Advertise...
Hello, my project is not going well. Trouble you Please help me again First of all, my English is not very good. I'm sorry. Can you provide an ideal sample code for me? My...
Hi
I'm using SDK 14.2, nrf52 DK and proximity example. When i try to write to inmediatte alert characteristic from nrf Connect ( android) i never get the event on the device...
Hi, in my project, the following codes caused "NRF_BREAKPOINT_COND":
sd_power_ram_power_set(4,(POWER_RAM_POWER_S0POWER_On << POWER_RAM_POWER_S0POWER_Pos) | (POWER_RAM_POWER_S1POWER_On...
