Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hi guys:
I was confused with the problem of "re-pair".
The condition is my device can only bond one phone (I was set the DEVICE_MANAGER_MAX_BONDS to 1).
Then I successful...
HI, I have nrf52832 and I am using latest SDK 14.2.0. I am using FDS and the problem is that before setting up BLE fds_record_write works fine but after setting up BLE all...
Hi there..
I've recently jumped back on development of a board I had made a while ago but have forgotten everything and am starting from scratch as computer was reformatted...
Hi,
I am trying to use nRF52840 boards but I am not able to write on them using JLinkExe nor nrfjprog. However, when drag-and-drop-ing a built example application, it works...
I want to use the radio interrupt to receive data, but I only entered the interrupt once at initialization, and I can't enter the interrupt again. But use the commented out...
Hi,
I'd like to know: when using Buttonless Secure DFU Service without bonds, wich is the proper way to prevent a central device to s et a new advertisement name for the...
Hello,
I've got some trouble using Nordic Uart Services,
I am using ble_app_uart example and after connection receiving bulk data from mobile app & sending it on UART...
Hi,
I have build pc-nrfconnect-rssi accodring to instructions. Though the locally build version responds very slowly compared to the officially installed version. No matter...
I am using a nRF52832 and v14.2 of the Nordic SDK. I have a question about the PWM Driver. I have the pwm driver working and driving an LED, but it is unclear to me how to...
Hello!
I am currently developing an application for the nrf52832 using Segger Embedded Studio as my IDE.
The application is not utilizing any softdevice but I would...
Hi,
We are using an nRF52832 with Soft Device S132 in a project. It has been requested that we should advertise as connectable with our own service and characteristics,...
Hi
In the NRF_MESH_PROV_EVT_COMPLETE event, I call
ERROR_CHECK(dsm_address_publish_add(m_next_unprov_address,&m_device_address_handles[m_next_unprov_index])); ERROR_CHECK...
Hello,
I want to be able to toggle blocking RTT output when using the log module.
Before in SDK13 I could just set SEGGER_RTT_CONFIG_DEFAULT_MODE to 2 in the sdk_config...
We are developing a system with multiple sensors that are spaced far enough apart that the furthest sensors won't be able to communicate directly with the user's device (also...
Hello everybody.
I just startet developing with nrf products and I'm facing a problem there.
I'm currently developing a System based on the ble_app_uart_c example. I'm...
