This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
Now I am using nRF52382 to make a product which needs a accurate one second timing. Then I use the project "nRF5_SDK_15.0.0_a53641a\examples\peripheral\rtc" and "nRF5_SDK_15...
Hi there!
Device: nRF52 DK
App: nRF connect
Compiler/IDE: Segger Embedded studio
SDK version: 14.2
Soft device: s132
Problem description: I am trying to run blood...
Hi,
I am reading a BMX055 via I2C which consists of three sensors with three addresses.
I got the easyDMA running to read 10 times the gyro using the PPI and the data...
Hello,
my first question is about TX carrier frequency accuracy measurement. The equation given in the whtie papers is
(|f_measured - f_programmed|) / f_programmed <=...
Why is the event length of the BLE Central HRS demo set to such a high value of 320*1.25ms = 400ms?
The demo seems to work ok with the BLE Peripheral HRS demo using the...
Does the Battery Service Client (ble_bas_c) module handle subscribing to notifications from multiple slaves? In my use case, I have the nRF52840 dev kit connecting to multiple...
I need to keep track of time on a device featuring the nRF52 and have an RTC run continuously in the background. The drift should not be more than a few seconds over a year...
Hello I try to use P0.09 as GPIO with this simple code but not working. (Works well with pin P0.08)
#include <stdbool.h>
#include <stdint.h>
#include "nrf_delay.h"
#include...
Hello,
I use the bootloader from the SDK SoftDevice 14.0.0.
I use the Laird module BL652 which have a nRF52832 component without external clock.
To compile the bootloader...
Hello Everyone,
I am working on nRF5 14.1.0 SDK, My question is how to generate "ble_app_buttonless_dfu_without_bonds_s132.zip" dfu file.
Can any one tell me the exact...
I am using nrf52832_xxaa and SDK 14.2.0.
Does app timer play a role in power optimization?
If yes, Can reducing the app_timer frequency reduce the power consumed by the...
Is there a BLE mesh SDK for nRF52840, and if yes is there anybody tested it? I'm going to switch to the nRF52840 from nRF52832 and it is very important for me to know it is...
Fanstel BT832 module mesh client stuck in nrf_mesh_sdk.c, 187, Initializing softdevice. When I upload the code on the NRF52 DK It works, but when I upload with segger embedded...
I have set up an environment to upload data to the nrfcloud using nrfconnect and the nrf52 dk.I can only upload data upto ff and then it resets to zero .The value which i...
