Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
On what occations do the BLE_GAP_TIMEOUT_SRC_ADVERTISING and BLE_GAP_TIMEOUT_SRC_SCAN events fire? The documentation is a tad ... terse .
regards,
Elm
Hy world,
I can update my device with FOTA, but the first time i do:
1 I put: "ble_default_bootloader.hex" on board;
2 i open nrfMasterControlPanel app
3 i write characteristic...
I have a feeling I am missing something completely obvious here. That said, this problem has cost me enough time today that I'm willing to risk embarrassment to see if someone...
I'm trying to implement a simultaneous broadcaster observer by calling ble_gap_adv_start() and sd_ble_gap_scan_start() and waiting for respective events.
If I call advertising...
Hello,
I'm trying to use Eclipse with a Nordic SDK (managed build mode) but it seems Eclipse (latest Mars edition) fails to invoke the assembler. Here is what I found in...
We are looking to use the DCDC to reduce the maximum current during radio operations, but minimize the overall current by enabling it as late as possible before radio use...
I have added button in my project and used bsp_init() to initialize it. All functions in bsp_init() returns NRF_SUCCESS but if I push my button even gpiote_event_handler(...
Hi Folks,
i have implementet a sleep mode by using only the RTC timer with the 32KHz OSC and the WFI instruction. The current consumtion is around 1.7µA (all peripherals...
Hello,
We have some problems with nRFgo Studio on the one of our computers.
Firstly, it takes a long time to flash firmware - about 15-20 seconds:
Secondly, we...
I have interfaced a vibration switch with nRF51822 Pin 19 using external pull-up. When there is no vibration the switch is either at open position or close position randomly...
UPDATED WITH IMPLEMENTATION
Is there a way to know what is triggering a chip boot :
Power off (battery replacement or deffective electrical connection)
The watch...
I have an old project I am trying to recompile for nrf51822 but have been programming with the most recent MDK on my station. The project is asking for old Device Family pack...
Hi all!
I just tried to compile the DFU example from the nRF51_SDK_7.1.0_372d17a and I keep getting the building error:
Referred Memory Range 'IRAM2' is undefined
...
Hello,
Does nRF51822 has a MAC adress when we buy it ?
If yes, is it possible to have two nrF51 with the same MAC adress ?
If yes, can we buy a MAC adress range and...
