Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi there,
I have tested out the BLE-NUS SDK firmware on the NRF51422 SDK Board, and it responded well. When I ported the exact same code over to my custom board, I received...
Hi,
I noticed that I can't bond successfully with my device using iOs 9.1 with Nrf Master control panel iOs app. When I insert the PINCODE, the device immediatly disconnects...
So I just received my nRF51 dk. When I plug it into the USB port, the device starts to blink but is not showing up as standard USB drive? Any suggestions?
Gabriel
Hello,
what general setup can you recommend to realize a Final Product Test only with BLE for mass production! (Without any additional copper contacts or NFC)
Some facts...
Hi I was reading up on all your chips.. NRF24, BLE and also on IPV6 capable..
Below are my requirements. Can you make a recommendation on what setup to use?
I have 4...
Hi
Im developing a filter - repeater signal on S130, and I want to advertise with a peridod of 20 ms for 10 seconds timeout.
I'm confused with FAST ADVERTISING AND SLOW...
HI ,ALL
i need to take use of the pstorage module.
i can read the data after reset,but i do not know the reason.
the write function is added in the on_write...
Hi there,
I have a nrf51422CEAA chip with 16k variant with single bank bootloader code. I compile it using (03) optimazation and the final result is :
"Program Size...
Hello,
I just produced my custom board with nRF52 but i have a problem.
I can program it (SWD over nRF52 DK), debug it (segger debudder software) but in bootloader it...
hi there,
I am using this tutorial to add dfu to nrf51422_xxac_s130 beacon application. however Im getting these linking errors:
._build\nrf51422_xxac_s130.axf: Error...
I was wondering what the procedure it for questions asked over the weekend. Obviously you guys are only available at office hours (Norway time I'm guessing?), so how do you...
I was kindly surprised with new S130 functionality - ECDH key exchange. Do you have plans in the near future to implement it in S110 softdevice? Thanks
Hi
I have nrf51822 CEAA which is powered with 1.9 volt on vdd (low power chip). I'm using ADC to measure battery level but the conversion gave me 5.4 volt wich is wrong for...
Hi,
we have developed some software that is running fine on the nRF52-DK (PCA10040 v0.9.0) which uses nRF52832 IC revision "Engineering B".
We are using SoftDevice s132_nrf52_2...
Hey everyone,
I am using nrf51 dongle pca 10031. Nordic promised to have 1Mbps data rate. when i was trying to transfer data through UART. data is validated until 401600...
