Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hi Nordic team,
I try to use SDK for Thread v0.10.0 cli example and run diag command, but it is disable as below
Could you tell me how to enable diagnostics module...
Hi,
I'm using nRF52840. I would use data length extension and set the MTU size to 247 when it works as peripheral. However,there would be some problem when it connect to...
Hi guys,
I want to know whether the provisioning beacon can relay by the relay node or not?
If not, when the unprovisioned device's radio is not in the range of the...
Hi Sir,
I'm studying the nRF52840-PDK, and i found there are two debug connector. One is Debug in connector (P18) and another is Trace connector (P25).
As check the...
Hi!
I am fully aware on how Eddystone works. Or at least I believe so. Sadly there is some weirdnesses when I am trying to broadcast using the Nordic SDK.
So what am...
Hello , ebery one
Please let me have a question about PCA 10040.
When you connect a USB cable, it acts as a virtual drive and if you copy hex format (such as Hart rate...
I'm trying to determine DFU_APP_DATA_RESERVED and FDS_VIRTUAL_PAGES.
According to this Q&A, DFU_APP_DATA_RESERVED must be the same FDS_VIRTUAL_PAGES, if FDS_VIRTUAL_PAGE_SIZE...
Hello,
I am using pca10040 and sdk 12.2.2. I want that my pca10040 should advertise for 10 sec then it should go to system off mode then it should wake up after 20 sec. My...
Hi everyone,
I was wondering if the nRF52840 DK will have NCP OpenThread support for wpantund Linux (other than Raspberry Pi) or if it already exists. I flashed the nRF52840...
Hello ,
I want to establish a connection between the adxl345 nrf51822.
Nrf51822 is working both individually and Adxl345. I would be glad if I can provide you with necessrat...
We are building a new version of a small device with the new nRF52832. Its only external connection is a micro USB plug that we use for charging - we do not need it as USB...
Hi,
I'm evaluating a nRF52 as ble central - controlled from a windows pc.
Searching the forum I just found:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/....
Hi,
I am trying to connect 4 devices with the pc-ble-driver. Therefore I modified the heartrate example.
3 Devices are connecting fine - on the 4th connection request...
I have been using nRF51 since 2013 in a lot of product. Haven't paid a lot of attention to nRF52 series because nRF51 has been a working horse and enough for our applications...
