Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
This is related to another post seen here:
devzone.nordicsemi.com/.../
Basically, I took the peripheral UART example and modified it so all UART printing was disabled...
Hi,
I am using
*nRF52840, SDK13.1, SD140, TWIM, easyDMA enabled. I have tried with the both 0 and 1 instance.
Looking in DSO, I am pretty sure that, after nRF is sending...
I edit the Tx power in ble_app_beacon application (0dbm and 4dbm) using this function and i observing the rssi values in nrfconnect app in mobile.i didn't find the differences...
I've compiled a new app with a new BLE service and module to go along with it (for different work than my other question, I can test this service in a generic LE explorer...
Hi All,
There should be a typo in " nRF24LE1_Product_Specification_rev1_6", page 82, Figure 35.
The Unprotected Program memory is shown 10 kB, but seems it should be 12...
Hi All,
I'm new to nrf51822. I'm developing a battery powered device using the Nordic ble_app_uart_s110_pca10028 peripheral example program. I'm glad to inform you my core...
i want to change the conn_params .
the first gap_params_init() ,
as below: gap_conn_params.min_conn_interval = MIN_CONN_INTERVAL;//20ms gap_conn_params.max_conn_interval...
hi everyone,
I've downloaded s140 and trying to run BLE notification example. I'm able to see state changes in the advertising on putty terminal at COM 7, but when I try...
Hi. i'm using nRF52832.
As datasheet says, flash endurance min value = 10,000.
Isn't there max value?
There is no limited life cycle for flash?
I just wnat to estimate...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hi,
We bought 3 nRF52-DKs (based on nRF52832 and PCA10040 V1.2.1). We compiled, built, and flashed the systems with several provided examples from nRF5_SDK_14.1.0_1dda907...
Hi,
I am working on a project where I have 4 sensors. Each sensor transmits(slave & Peripheral) its value using BLE to the Receiver (Central & master) which is also BLE...
I need to create a service on the nRF52832 that can send large amounts of a few different data types to the central device. For instance
ADC1 sampling (~256 bytes/s...
I'm wondering which is the proper way to adjust the ANT power level?
I've seen some posts that seem to suggest that the proper way is by the use of the the BLE Gap call...
