I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
I was working with examples/ble_peripheral/ble_app_gls. In the SDK11alpha configuration, I paired the dev board with my Android phone running nRF Toolbox and was able to start...
Hi,
I loaded S110 v8 to nrf51. Then I loaded dfu_dual_bank_ble_s110_pca10028 bootloader.
With this setup, I'm able to download my application via the bootloader.
The...
Hi,
Reading the nRF52 product specification, I see:
"If the antenna is exposed to a strong NFC field, current may flow in the opposite direction on the supply due to...
Req: from the cap-sense board, different tap will be done by user (like 2 times tap, 3 three times tap etc). so the Bluetooth board (nrf52) will receive these taps as interrupt...
Hello Devzone fellows :)
As you may notice, we have posted our first webcast: Interfacing with Nordic's Softdevices .
It's the first test run in a series in which we...
Anyone knows which Nordic chips they have used in this device, and do you know if it is possible to get it to Arduinio?
www.tu.no/.../345999
http://sfty.com/#produc...
Hello,
Some little compilation errors.
in ble_radio_notification.h
typedef uint8_t nrf_radio_notification_distance_t; => is no more defined in SDK but used here
...
I need to do an hybrid app like nRF UART App but with cordova. i can connect and disconnect, but i don't know how to catch the data every time the ble send.
i'm using this...
Dear all,
I make a simple test on the UART0, putting the code in 'simple_uart.c' to my main.c. When I send out a character 'A', 0x41. From the CRO timing, it appears that...
Hi all,
I am developing ble mesh network, the source code taken from this link: github.com/.../nRF51-ble-bcast-mesh . First i tested led mesh example for two boards.
...
Hi, I need to use whitelist in ble_app_uart example, What are the steps that need to be followed for that. Is device Manager is mandatory for using whitelist. Can anyone throw...
Hi all, i followed the tutorial " devzone.nordicsemi.com/.../" and did the challanges, however there is a detail i don't understand (totally newbie here!): the value of temperature...
Hi Nordic Community and Developers,
I'm designing a small Bluetooth module using nRF51822 to use it in my next projects and I need to use thinner substrate material (~0...
I have an application that we have ported to the nRF52 that used an EEPROM to manage configuration values. This application doesn't update these values often but when they...
Hi All, we have used Arduino modules based at 24L01+ in our application, now we are getting to apoint where we need to find one of theese or another one and do a redesign...
