Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello Nordic Team,
I’m using the nRF9151 DK board in Surat, Gujarat, India with a valid Onomondo SIM card . I’ve followed the setup instructions as per the Nordic Academy...
Hello, I am trying to update the modem firmware to v1.3.7 using UART using the nRF modem bootloader API. For context, I am running nrf-sdk 2.9.1 and also using the SLM application...
Hi,
We’re working on a device using the nRF52832 and have DFU over BLE working correctly using internal flash. Updates work both via our custom app and the nRF Connect app...
Hi,
I believe 2M and 1M are OK to adjust, however, long range code added the extended advertisment, I am curious whether I can update these three PHY all together.
Thank...
Hi
I noticed one ticket says that "the following combination offers low power consumtion and high througput when needed :Short Connection Interval + High Slave Latency ...
Hi, I'm a beginner and I'm trying to run an LED blinking program. However, I'm encountering a device-related error.
I've followed tutorials and installed all the necessary...
Hi,
Our project requires an unusual combination of running BLE, Gazell, and raw radio packets for time sync simultaneously.
Time sync and BLE are infrequent activities...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Hey folks,
i have to use the nrf9160 board to create a PoC for a project of our company. The main topic of the PoC is not important here because i cant even connect to an...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
Further into development of the ReRAM file system. I noticed that in generated DTS for nRF54L15 board for the ReRAM we have:
What is the reason for providing erase-block...
I am trying to compile hci_lpuart for thingy91_nrf52840, but I have these issue. hci_lpuart:
Any ideas on how to solve this? I'd really appreciate it. And if you have any...
Hello, we are trying to receive BLE extended advertisement pakcets from Thingy53 using a nRF52840DK as a HCI controller with a Raspberry Pi 5. I am using a nrf52840dk as a...
