Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
I am currently working on the secure_bootloader example (pca10056_s140_ble) for the nRF52840 DK board and am encountering an issue with updating the OTA application. I have...
Hello, I connected my (working) PPK2 and opened the PowerProfiler. Immediately, a "DFU needed" message popped up.
I DFUed the PPK2, and in the logs, it wrote DFU successfully...
What should be format of USER Certs for Matter factory data?
CONFIG_CHIP_FACTORY_DATA_CERT_SOURCE_USER =y
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello DevZone,
Is it possible to support Matter over Ethernet and Matter over Wi-Fi at same time?
Since there are many Ethernet chips support in Zephyr.
Seems that the...
Hi,
I'm looking to continuously sample the ADC at a high sample rate with rotating buffers.
I found an example code that matches what I need with the older SDK for...
We are using nRF5340 with nRF7002 on our custom board. Our application requires:
Wi-Fi (via nRF7002)
Thread (via nRF5340)
DFU over Wi-Fi
We are concerned...
We have peripheral, and we want to connect it using NRF 52840. when we are bonding this using nrf connect app we get a pop up with random key and using pair we can pair with...
I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
Hello,
I am currently using the `AT%XICCID` to obtain the ICCID of Hologram eSIMs. The output of some of these eSIMs are just the raw 20 digit ICCID with no ending checksum...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Hi I am trying to get an SD card hooked up to my nrf52840 devkit. I am using nRF Connect v2.6.1 and I was trying to get the sample code working, so I used the sample in ncs...
I have downloaded nRF connect setup V5.1.0 and nRF command line tools V10.24.2.
downloaded nRF connect extension , SDK pack and tool chain in VS code.
I added the build...
