Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
Hi i'm a newbie in nordic chip. Can someone please explain to me that how to enable and configure the timer interrupt and what kind of setup need to be done?
Example in...
There is a mistake in LEDS_INV_MASK definition:
PCA20006.h / nRF examples 10.0.0
#define LEDS_INV_MASK 0x11111111
// blue will be erratic
PCA20006.h / nRF examples...
Hi,
when i setting up a new project in uVision, i get a crazy Error wich i cant handle with.
My error is --> main.c: error: C3906U: Malformed via file '.\main.__i'....
Hello,
in the new version of sdk (11.0.0) you support s130 only.
That means the code contains both peripheral and central implementation.
Does it mean that s130 consume...
The following seems to suggest each write event can only contain 1 byte of data at a time.
/**@brief Event structure for @ref BLE_GATTS_EVT_WRITE. */
typedef struct...
Been playing with NRF24L01+ for a while and mostly they work as I expect. Now, I'm trying to use an ACK payload, but whenever I try to set up the receiver to put a payload...
Hi, I'm using trying to use the DFU via BLE, dual bank example from SDK 8.1.1 (with SD 8.0.0) and got it all working up to the point where I call "activate image and reset...
Hi,
I have a problem that the ANCS keeps resetting my board, so I was able to reproduce the problem on the PCA 10028 dev board.
Conditions:
iOS 8.x or 9.x
No...
Hello,
I am running Windows 10, nRFgo Studio 1.21.1 and Keil uvision 5.16a.
I was doing some tests with my nRF51 DK board, like loading the beacon example found in the...
Hello,
I am using simple_adc__pca10028 from 8.0.0 SDK to read values from my sensor, its a kind of tensometer. My configurations are:
NRF_ADC_CONFIG_RES_10BIT...
Dear sir,
I am using your NRF24L01+ chipset with STM32F407ZET6 controller for 2.4GHZ RFID communication. can u please share the STACK for this controller.
I have a few questions (using nRF51 DK and/or external nRF51822)
I use an analog pin to measure the voltage of a capacitor of an analog circuit. From time to time...
