Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
Hello,
I've downloaded nRF5_SDK_v11.x.x and install it, my keil version is v5.14. I flashed s130 v2.0.0 into nrf51DK, then build "ble_app_beacon" basing on SDK v11.0.0 and...
I use the S110-6.0.0 to find the iphone ANCS service,return attr missing. The 16bits UUID is xF431.I have added the long UUID ble_uuid128_t ans_base_uuid = {0xD0, 0x00, 0x2D...
Hi~
I used keil software environment for development.
Apply Ble UART example code from nordic keil example.
Example code down load to nRF51 Development Kit and run, program...
Hi, i need to calculate the frequency of two PWM.
When it comes to frequency calculation, the counter function is the best solution, i think.
i'm using SDK 6.0.0 for...
I want to develop an app that wakes app from sleep mode after pressing 2 buttons, then if these buttons are still pressed for 5 secondes i want to do an action ..
Any idea...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
Is there a call to read the stack ID.
For example S120 v2.1 has an ID of 0x006B . nRFgo studio is able to read and report this value.
Is there a way to read for me to...
I'm using SDK 11.0 and example\ble_central\ble_app_hrs_c
I have cut SB1 SB2 to disconnect the 32Khz crystal from the pca10028 and configured the example program to use...
Hi, When I write data synchronously to memory (nRF51822), I do :
APP_ERROR_CHECK(pstorage_block_identifier_get(flash_handler, 2, &block_handler));
APP_ERROR_CHECK(pstorage_clear...
Hi,
Im having a problem with connecting my phone to nrf DK.
im trying with apps from examples and they work well with HTC one, but my Samsung S6 fails to find device ...
I flashed dual bank ble bootloader from newest SDK (6.1.0) and used it to load my application to chip. I also modified my application (according to instruction here: devzone...
Hi, I have two device. S120 Scanner and S110 Peripheral Device.
At Scanner, I use SDK 9.0.0 and S130 1.0.0, At Peripheral Device, I use SDK 9.0.0 and S110 8.0.0 ..
Scanner...
hello,
I have a custom board which works fine with SoftDevice+Application , but if i Combine a boot loader hex that i complied it doesn't work. But the same ( bootloader...
I found and implemented an example that gives me a decent idea of how to go about polling for data with the UART/FIFO. However this doesn't give any indication of how to use...
