We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Or may be another procedure to make a list of surrounding beacons nearby using nrf52832. We are beginners, sorry.
What do you recommend to start with?
Sdk16, 7.0.1 Softdevice...
Hi,
I have configured pin 10 (STATUS_BUTTON) on my own design board using a nRF52832 chop as follows:
I am intending to use the internal pull-up resistor to pull the...
Hi,
I'm trying to emulate a server device with pc-ble-driver-py, I recently moved from version 0.11.4 using Python 2.7.12 to version 0.14.0 using Python 3.7.4. I'm trying...
Hi,
I am using segger studio and NRF52810 for my development. I started with the NRF52 dev kit and complied with the sample app given in PCA10040e folder.
Now I want to...
Hi All,
I'm trying to figure out the best way to implement the security between two industrial IoT devices. We don't have a good out-of-band channel for more "traditional...
Hi,
I'm using Thingy:91 and I have built and flash the asset tracker software. I have connected the external GPS antenna (MIKE3A or similar), see picture.
How do I check...
I am using nrf52832 chip along with softdevice as a peripheral. There is a requirement wherein we want to encode the advertisement data.
Came across ble_advdata_encode(...
I'm reviewing the ringbuf library for use with FreeRTOS across two threads and I can't see how the atomic operations implemented in the library make it thread safe. The atomic...
My debug uart stopped working after creating overlay files to make port changing easier. Is this a known issue? They're still the same pins and baud rates.
Hi, I have done a project in my DK52 using the ble_app_uart as base program, it is working very good in my evaluation board but when I download the program to my final target...
Hello all,
LED3 from nRF9160 DK doesn't blink after I erase all with SES.
what I've done so far:
Update successfully the modem to 1.1.0
Load the applikation 'nRF9160_DK_board_controller_FW...
Hi,
Is it possible to list down all available device to my console using static provisioner code on nrf52840DK using bluetooth mesh stack?
Thanks for your valuable...
Is it possible to connect an nrf9160 to more than one broker?
We are intending to use one broker for publish/subscribe topics and another broker for OTA updates.
QUESTION(s): Is there such a thing in BT spec that allows for a device to rebroadcast advertising data for another device? Sort of like a flood mesh. Could it be iBeacon specific...
Hello Nordic community,
I found three IC on BLE 5.1 are nRF52811, nRF52833, and nRF5340.
I have to choose one IC for my new project based on availability of SDK and RTOS...
