Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
I am using mesh SDK 4.0.0 and nRF SDK 16.0.0. I ported the ble_app_uart_coexist example from mesh SDK to build OK for pca10056 board (nRF52840) by following the instructions...
I'm attempting to receive SMS in eDRX mode. It succeeds when nRF9160 device is left in a place without moving it.
However, when I move it to a far place like a few kilometers...
Hey..
I'm using the nRF52840-preview evk, with the Arduino camera plugged into the side connector. PCA10056_USE_FRONT_HEADER is set to 0, and I'm using the SES project....
Hello, guys!
I recently started playing with nRF9160 SiP module. nRF Connect SDK is properly installed and I am able to build the code and download it properly. I also spent...
I have a nRF52832 Breakout Board, in which i programmed using arm cortex debug connector, using Segger Emmbedde Studio. I uploaded one example from nRF5_SDK_15.3.0, the propramm...
Hello;
we are having a communication issue(a BIG one at this point) that we are experiencing with our BLE 4.0 tablets. Our device(has NRF52832) is designed to communicate...
I noticed some weird behaviour which I can repeat to do with not being able to register after reading back the ICCID.
The following after the list of commands I run on bootup...
Hi,
I'm trying to update the FW of my nRF9160-DK.
Running MacOs Mojave 19.14.6. Installed nRF Connect 3.3.0. This is the log after startup of nrf connect:
2020-01-24T15...
Hi
I've checked the two PWM examples in SDK, pwm_driver and pwm_library, they seem too complex for me to understand, does anyone know where I can find a simple PWM example...
Your download page for nRF-Command-Line-Tools is not working and it redirects to "page not found (Error 404)". I am using this link https://www.nordicsemi.com/Software-and...
I am currently working on a project where I am checking an input > 3V then passing it to ADC and increasing count based on it. The count value increases or stays the same...
I'm going to write to inquire about Bluetooth Low Energy Device Beacon which will be smallest in size and can operate with coin cell battery and also able to communicate two...
Trying to build the app from C:\Users\xxxx\Documents\SEGGER Embedded Studio for ARM Projects\nRF5SDK160098a08e2\examples\ble_central_and_peripheral\experimental\ble_app_interactive...
Hi
I'm working with the following products to develop a product and have chosen to use a IDE based around Arduino and Visual Studio Code. This iDE along side off the shelf...
