Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
We are building project with this config parameters: But we get this error messages while compile: If we use CONFIG_LOG =n for mcuboot, then project compiles normally. Also...
Hi,
Is it possible to make the MQTT connected device receive the Shadow config updates and AT Commands immediately? Based from our testing, the device only receives the...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
I am using two nRF5340 Audio DKs one as a gateway and the other as a headset. I tested the nrf5340_audio example and managed to get the speaker output working through the...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic,
I want to implement a LED blinking like below pseudo code. I'd like to use PWM sequence Timer x n , GPIOTE, PPI since it doesn't consume any CPU time. for ...
The functions “ nrf_log_frontend_std_...() ” called by “ NRF_LOG_INTERNAL_MODULE(...) ” use only 4-byte (uint32_t) arguments, which is not suitable for arguments of type ...
Hello
I want to clarify something because there seems to be a lot of conflicting information on Dev Zone, and the nRF5340 DK documentation doesn't specify the following...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
Hi,
I am trying the system_off sample of Zephyr version 4.0.99: https://docs.zephyrproject.org/latest/samples/boards/nordic/system_off/README.html
The sample works...
Hi,
I have a problem with nRF52832 after entering the radio RX state. I use a proprietary protocol with fixed packet length. Packet transmission works fine, receiving the...
Hi, We developed our custom BLE electronic board based on the nRF54L15 SoC. On this project the nRF54L15 firmware setup a SPI slave interface in order to receive commands...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
HI
I am developing an LCD using the GC9A01 module. I implemented it by referring to the code as below and it works fine.
https://github.com/Exboom/GC9A01_nRF52
But...
Hi there,
My nRF5340 application requires the use of SD card with DMA and BLE transmission. Howerver, as soon as I turn on the device, I get the following errors:
A...
