I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi!
I'm fiddling around with the PCA10040 and the experimental_ble_app_blinky from the SDK found in examples/ble_peripheral/experimental_ble_app_blinky. I've had great...
Hello,
I'm trying to write value to a specified address with ble_flash_page_write .
I'm using ble_flash_page_write after ble disconnect event. I've tested different...
hi Ole BAUCK, my slave device is STPM33 ENERGY METER using this device we can calculate vrms,irms,real power,reactive power,energy and many more.. that device is not having...
Hi,
i'm doing my own bootloader and i want to use external flash to download image trough a spi. Now it almost works. But after an app image has been successfully transferred...
hi all,
i am using sdk v8.
i want to transmit the address through uart and read the data using UART.
i am using app_uart_get and app_uart_put api's.
PROBLEM:
if i connect...
Hi, it says that I have to put my beacon into beacon config mode in order to configure beacon device through the app. How do I enter beacon config mode in my nRF51dk? When...
Hi, In my project I need to measure current values for every sec and update those values to advertising data. So, I take manufacture field in advertising data to update the...
My set Up: Nexus 6 (Android version 6.0) as Peripheral, Nordic as Central.
I want to achieve ble pairing using 'pass key confirmation' methodology.
The nordic device has...
Hi Nordic Developers..
I am using nrf52 with softdevice 132.
In my project i am using external EEPROM(Microchip 11AA010) that uses UNI/O protocol and Single I/O Serial...
I'm using SDK 8.1.0 (SoftDevice 7). I built a version of dual_bank_ble_s110. Installed both on a freshly erased pca10028. It comes up fine and sets the LED on. It's advertising...
Hi guys,
I'm facing some trouble to put my rtc working properly. I made a code based on the rtc example but it's not incrementing the time the right way.
Bellow follows...
Hey,
I have written a custom service for my company's sensor readings on the nRF51 DK, on top of the uart peripheral example given n SDK_11.0.0. However, for the final...
What should be done if we add nRF51822 SDK into our code for business (redistribution)? We have our own IDE and would like to integrate "nRF5_SDK_11.0.0_89a8197" into our...
I wanna plan to design a new hardware which has ability to connect to smartphones using BLE and broadcasting ANT pages in the same time. I also need a way to transmit some...
