Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi,
I am developing a firmware using nrf51822xxaa s130 SDK 10.0. I am using device manager to exchange the security keys and storing the bond information. For my project...
Hi, If I understand correctly the debugger on PCA10040 can operate in 6MHz/n as SWO frequency.
the nrf52 can operate at 4,8,16,32MHz swo frequency.
How are we to use SWO...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
I'm trying to implement the DFU Feature into my application, but it seems to be in a bootloop after it starts advertising.
The application works fine when flashing it via...
Hello everyone, I want to measure Low power mode current consumption in nRF52 DK,but I dont have accurate CRO to measure in micro Amperes, therefore I would like to know if...
the eclipse build memory map is
text data bss dec hex filename
363312 2485 5340 371137 5a9c1 ********.elf
363312 2485 5340 371137 5a9c1 (TOTALS)
it is giving very large...
Hi Friends, I like Nordic and Arduino, it's great if Nordic can support Arduino officially, we can use the ARM0 in Nrf51822 as a single control point of Arduino project. There...
I taken the Android-nRF-Beacon-for-Eddystone app code from github.
From my account I configured my Google Dev console:
enabled proximity API
added credentials...
Hi all,
I followed the tutorial listed below:
devzone.nordicsemi.com/.../
I want to use SEGGER_RTT_printf but I always get this error:
Error: L6218E: Undefined symbol...
Hi,
I am working on one project in which I want to connect my two custom borads with S130 softdevice but I am not able to do that. My custom board has nRF51822 chipset...
I would like to implement a simple code to use SAADC on NRF52 to sample one channel at maximum sample rate (theoretical 200KHz).
All the examples I have found use limiting...
Hello All,
At a time either ble nus or dfu can work.
I have an problem with the services ble nus for uart and dfu does not work simultaneously means if i am adding both...
Hey, I got 2 beacons which I have connected via BLE successfully however I have some problems with BLE_GATTC_EVT_HVX event. Every time I get only one BLE_GATTC_EVT_HVX event...
