Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
We would like to enable the flash protection for an nRF52 application with the typical scenario:
to disable flash reads from the JTAG,SWD interface; only erase/reprogram...
Hello everyone.Recently I try to send some information from a "nrf51822" to phone when they are connected .So I choose "ble_app_hrs" example program,and I add two characteristics...
Hi everyone
I am working with nrf51 and I need to know how much my specific code occupies in the flash memory (I know how much is the available memory).
Thank you
I have two board - 51422AC based PCA10028 and 51822AA based custom board. Custom board doesn't have 32768 OSC.
My goal is to let custom board work with example project...
I want to use my stand alone SEGGER with nRFgo Studio. How do I do that?
It looks lite nRFgo Studio only recognises the PCA10028 board as a SEGGER but not my stand alone...
I have a ble_uart application which is working when I load it on the chip. But it will not automaticly run again if I unplug the supply and just plugin again. When I unplug...
hi,
i am using eclipse IDE to build the blinky example with soft device s130(using SDK11). i added the make file and .ld script and linked all files which is required....
Dear Nordic family,
I tried programming Raytac MDBT40 with the LED blinking code (taken from the example project of SDK 8) which worked with nRF51822 Bluetooth Low Energy...
Hi
I have been using the DFU for quite a while. I adapted the boot loader to my hardware and compiled it using Keil.
All my other code is written in another environment...
Dear Nordic Developers!
When I call the sd_power_system_off() function to put the MCU to system OFF, after that I can still see the advertiser device in MasterControlPanel...
Hi!
First of all, I'm using the nrf52 PCA 10040 DK, with SDK11.0.0, and my Soft Device is 132 2.0.2.
I'm developing an app for comunicating with a sensor via SPI (send...
Hi,
Am starting custom service to support custom profile and it works without any issues.
But when I add DFU service also to start after custom service DFU service fails...
Hi All,
I have a question about use of super/ultra-capacitor in a circuit using a module BLE (nrf51822 inside) instead of accu Li-Pol / Li-ion ?
it is possible to use...
I am looking to use the nRF51822 in my product and have been given a nRF51822 development kit however i have been looking for access to the Firmware and Hardware files and...
