Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi,
I programmed my NRF51 to read ADC samples and I trying to transmit the information to a dongle. So far I have been able to send the hexadecimal values of the recorded...
Heyho!
Is it possible to set the PWM base clock frequency to 40kHz? If so, how? I see that the predefined base clock frequencies don't go any lower than 125kHz.
I'm...
Hello everyone, I am program for PCA10001 and I want to use Bootloader to upgrade firmware through OTA for my device. I have a old file bootloader use for s110, and I tried...
Hey,
I would like to send data from Central to Peripheral. I follow by ble_app_uart example, however I need to send a float type variable, so I split it to the total and...
I have 2 identical nrf52832 development boards with PCA10040 V1.1.0. One is running the ble_ant_app_hrm example from the nRF5_SDK_11.0.0_89a8197. This example appears to run...
Hello,
I'm developing a product using nRF51822 which is intended to work with iPhones (only iPhones for now; iPod/iPad and Android later).
I need some kind of document...
Hello,
I'm trying to recreate the PWM_library example from the v.11 SDK in a new file in Keil. I have compared the debug settings in my project to the debug settings to...
Hi there,
I am following the thread to use JlinkExe and JlinkRTTClient. I encountered a situation which i don't understand.
After running JlinkExe (go to the folder...
Hello,
I am trying to remake an nrf52 project in Keil and ran into a problem regarding stdint.h. There is already an "include <stdint.h>" statement and Keil has not reported...
Hi,
I am testing the NUS using the UART example in the SDK11 with the PCA10040 board.
Since I want to achieve the maximum speed of transmission I used the FIFO buffer...
I am having issues waking up nRF52 with s132 using the RTC interrupt. The same code is used on nRF51 with s130 and does not show this behavior.
The RTC is configured and...
Hi,
is it possible to have the same configuration as in the example ble_central_and_peripheral but with ant+ as peripheral (on nRF52)?
Thank you for your attention
I am doing externally triggered SPIM transfer on the Nrf52 using PPI.
I found that the NRF_SPIM_TASK_SUSPEND is a very power hungry operation as SPI suspend waits for the...
Hello
I have a nRF52-DK and I am trying to programme an external designed by myself but this one contains the nRF51422 chip. I am using nRFGO Studio to upload the .HEX...
