Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
I am using nrf_toolbox on Windows Phone 8.1 and PCA10040 development board. I loaded the uart example and with my phone I can send text via nrf_toolbox. But when I want to...
Im' trying to send a set of 80 bytes using indication. for that I have a characteristic sending each time 20 bytes and wait for indication acknowledgement before sending the...
Hello Nordic! My application requires an nRF51822 using S110 to handle both Notifications and Indications over the same characteristic.
The CCCD value 0x01 = 0b01 enables...
Hi,
In order to start my own board with nRF52 component throught SWD, I think I've to use Segger Jlink. I expect to buy the basic version, that sound good for me, but I...
Hi,
I have some problems with bootloader debugging by using app_trace_log().
My board is pca10028, and I use the SDK 10.0.0 for it. The Keil version is v5.20 and Jlink...
Hello All,
How to interface nRF905 with nRF51DK board?
Any driver is available for nRF905 which support nRF51.
Any help will be appreciated.
Regards,
Rajneesh
Hi,
I'm using PCA10028 to communicate with ADS1131 ( www.ti.com/.../ADS1131) which outputs 18bit on SPI bus. I managed to get the data out by reading 24bits, but it feels...
Hello ! When I make a read with the SPI from a sensor's register the data sometimes comes correct and most of the time wrong. I tested the read operation with an Arduino and...
Hi
what is the best way to implement a sleep after disconnect?
We are using a custom board and I implemented it this way:
on connect : turn advertisement off
on disconnect...
I used iar for my project. But for some reason I have to transfer my project to keil now. Attached is the icf file from iar and I also attached my keil settings. Now the system...
In following the example for a DFU BLE upgrade I have configured the following system
on an nRF52 DK install the softdevice and bootloader:
nrfjprog --family nRF52...
In my code, I have some 'print'-style functions that write data to a buffer, and that buffer then goes to the Nordic UART implementation. This is user code, and I don't know...
Hi, I'm trying to adapt the stm32f4 library from:
link text
to run an nrf24l01+ with an stm32f373. After some initial SPI headaches, a lot is working. In the initialisation...
I want to confirm how much current is being drawn from the battery while the nRF52 is in it's absolute lowest power state and waiting for an NFC field to wake it up. From...
I am interested in setting the tx power level the advertising packets in a nRF52832 are transmitted with. I saw there is the TXPOWER register in the RADIO section (address...
