I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi,
On a nRF51822 (QFAAG0) with S120 softdevice (using the recent PCA 10001 v2.2.0 board), i'm trying to perform these operations successively:
a simple RSSI scan...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi,
I want to use the AES of 51822 and I have read the nRF51_Reference_manual,I cann't find any demo about AES in SDK.Do you have the demo code about 51822 AES encryption...
Help please! I've been using the nrf51822-EK for several months. Everything has been working well.
I updated my SDK in order to be compatible with S110-SD-v6. Everything...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
am using nrf51822 chip communicating with PIC16fl1509 through uart.the PIC will send the temperatire values through uart to nrf51822. i have a doubt ! will the uart communication...
Hello,
The fact is that I was testing how to OTA update the kit's firmware. I had no problems with the app but when I tried to upload the bootloader.hex includen in the...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
friends :
i assume that the nordic support team can also be considered as friends.
i purchased a nrf51822-mkit, but it seems that it does not qualify for a legitimate...
Hi guys,
I would like to know how to use the softdevice to enable an interrupt when I receive an advertisement packet. Right now I know we have to use
softdevice_ble_evt_handler_set...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Good morning,
Is it planned to raise a new version of this application note but based on the new version of the SoftDevice? If yes, when is it expected?
Best regards...
Where could I find the software for the Connectivity chip(ATSAM 3U2C) that enable the mbed connection?
If I flash the EK board with this software, could I use EK(evaluation...
Prior question: nrf51422-soft-device-options
As a follow up to my previous question, has Nordic developed a stable boot loader to use with the S110 soft device and the...
