Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi all,
I've been wanting to start this project for awhile now, but I am having trouble figuring out where to start. I want to be able to make an iphone application which...
I try to optmize my code so it can run on the 128k chip.
My issue is with pstorage: I have 7 variables (from 4 bytes to 20 bytes) that I store in individual blocks. But it...
I have the nRF51 Dongle and an nRF51822 BLuetooth Smart Beacon kit. For software tools I have IAR's EWARM 6.7 for a complete IDE or command line GCC/GDB.
Are there any...
Hello,
my idea is to turn on a GPIO-Pin of the NRF51822-Beacon-Kit when my smartphone found the beacon. Of course if the smartphone is out of range or far away the pin...
Hi all,
I am trying to figure out how to change the LEDs blink rate on the go.
I have set up the timers_init() and let say every 500ms sensor data is read on dev kit...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
Hi,
I'm trying to get the actual connection interval used between my nRF51822 device and iOS device.
I have read this article , but I cannot get it worked.
I used sd_ble_gap_ppcp_get...
Hi,
I want to disable the softdevice (S110) in order to use the "flash_page_erase" and "flash_word_write" functions. But, when the sd_softdevice_disable() is called I get...
Hidden in the guts of this answer is:
Please be noted that not all central
stack have full support to
automatically discovery secondary
services (e.g S120 stack)...
In the code for the bootloader in dfu_dual_bank.c and the function dfu_init , I currently get an error code on timer start: 4 ( NRF_ERROR_NO_MEM ).
err_code = app_timer_start...
The device name is set in the usual way at the start of gap_params_init():
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode);
err_code = sd_ble_gap_device_name_set(&sec_mode,...
Hello,
I am new to BLE profile development. I searched in web but could not find out a useful guide for this in terms of actual implementation(coding). It is seen that all...
Why is the "old" EK "not recommended for new designs"? Will the old EK work with the IOT SDK?
(Maybe it is chip rev dependent? I don't have the my EK on hand so I don't...
Hello,
I have purchased a Intel Galileo Gen2 (x86 Arduino) and RedBear BLE shield v2.0. The Arduino IDE I use is Intel's version. I have imported the corresponding libraries...
The application uses bsp_button_is_pressed() but this device has no buttons. This results in err_code set to NRF_ERROR_INVALID_PARAM and subsequently a system reset during...