Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I recently started working with the NRF51822 and PCA1001
I need to read data from MPU9150 accelerometer via I2C and transmit the results over BLE.
I connected the...
Hi,
I'm communicating ANT through softdevice ant event handler as follows:
err_code = softdevice_ant_evt_handler_set(on_ant_evt);
void on_ant_evt(ant_evt_t * p_ant_evt...
Hi,
I'm using PCA10003 board with nrf51422 chip with version E0 and tried connecting ANT with ANTware II software using the HRM example and it works fine on UART but on ANTware...
Hi,
I'm using BLE and ANT+ concurrently with nrf51422 and s310 softdevice. I'm using on_ble_evt for BLE and on_ant_evt for ANT+.
I'm using following code for advertising...
Hi,
I want to add a bit (about 100KB) off data to my project in Keil.
I need to work out where to locate it (to avoid my code and the S120)
I can't seem to find a memory...
Good morning,
I have taken a look to different information related to this topic but I'm still confussed about the way to proceed in order to implement the way of working...
I am trying to use the dynamic payload length feature, but I am not sure of what settings to use for the RX_PW_P0 - RX_PW_P5 registers. According to the documentation, for...
Hello,
We are going to use nRF51822 in our product.
Use case is as follows:
Connect with android/iOS phone and receive some configuration data.
Connect...
Dear Sirs,
I'm using nRF51822 EVKit and using example code "button_radio_example" for pca10001 device and measured current consumption on this PTX device and found out...
I just want to handle phone simple call event from iphone4s.
How can I do? Is there any other way to do this?
There are so many media key in hid profile, is there any...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi guys,
is it possible to get the mac address of the connected device?
Didn't find anything in ble_evt_t ..
Thanks!
Edit:
Sorry, i found it:
its in the ble_evt_t...
i am new to nfr51822 and i am doing project on indoor localization in which i need to read the RSSI values of bluetooth. so how i read these values? and i have setup the evaluation...
