I am developing an server app on zephyr stack which requires to flash the image without SMP protocol, I receives the image data over BLE , how can I use Image management API...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hi,
Im using Keil, S110 6.0.0 and a ble_app_hrs demo code.
I get a problem that the code hangs in sd_softdevice_enable. The board is a copy of the board from the dev...
I am using the sniffer with Wireshark to watch some data being passed by my central and peripheral. I started with the multilink central and peripheral examples. Unfortuantely...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
Folks,
Here's a specific question and a larger question, of which the first is a part.
What's the proper way to insure S110 BLE stack cleanup on disconnect due to...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi all,
We're currently working on the project with includes external ADC. The SPI interface is used for communication, we're using spi_master library from the newest SDK...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
I have an nRF51822 based peripheral running SD 7.0.0, using SDK 6.0.0. It has a custom (vendor specific) characteristic which is read/write.
If I use BLE_GAP_CONN_MODE_SET_OPEN...
Hello Guys,
I am interested in what is the packet size of Heart Rate application board example included in nRF51 SDK 6.0. I am using nRF51822 Evaluation board. Could help...
I am working on nrf24l01+ which interfaced with atmega32. I received data but it take time to receive (appx. 1min). I set RF_SETUP to 0x27 ,disabling auto ack and sending...
I consider to use a 32k MEMS oscillator instead of a usual 32k quartz crystal with a nRF51822 (WLCS). 32k MEMS oscillator's package is quite small 1.55 x 0.85 mm, there's...
I am developing on a custom board using nrf51822 with pure gcc. The blinky makefile worked fine. Before going to ble_hrs makefile, I want to load the blinky_example with softdevice...
hi guys,
i've a general question about bluetooth (general usage of characteristics), and i hope somebody could give me a hint how to use them properly.
So, i want to communicate...
Hello.
I've tried linking the ESB library in IAR but I am still getting error.
When link arm_lib.lib getting this error:
Fatal Error[Li014]: error when reading "nrf_esb...
