Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
I want to load a Blinky project to the AK board, and the dongle is used as a jlink, but I forget to move the jumper to the 'out', and the program is loaded to the dongle....
Hi,
I change the example ant_broadcast to acknowledge mode, but it seems that without a peripheral side,the LED0 will still twinkle.I don't know how to change the project...
Hi,
I'm porting a nrf51822 evaluation board 10001 tested application to a custom board. Part of the application is using UART interrupts to raise a flag and start data...
I am experiencing an error in the final linking stage of my build.
_build/blinky_gcc_xxaa_s120_xxaa.bin: file not recognized: File format not recognized
collect2.exe...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
My application seems to be running out of memory, now I received NRF_ERROR_NO_MEM from sd_ble_gap_ppcsp_set. I don't understand why this has started since I don't think i...
Im using custom board with nRF8001. I'm using Hello World example from GitHub.
The nrf chip revision is C not D. When I connect the board to Arduino Leonardo the device start...
Hi
I ran the example " ble_app_hrs ". the consumption is 1.5mA, when I hold SWCLK and nRESET low,the consumption is fall to 0.9mA. how I could reduce the consumpion??
I can input "hello" in win8.1 with button 0
==
before text in iphone5
I change
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(16, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL...
Hello,
I am searching for an exampleproject to learn how to connect to motherboards (or an evaluation board)
over bluetooth:
I try to send data from on chip (nrf51822...
It seems that is not possible to rewrite data on a block ?
I want to persist some data. The first time (after erasing all the flash memory) I store a data on a block, it...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
