Hi,
I wanted to implement a version of Channel Sounding where you wait for a certain amount of distance estimations, and then try to just select the smallest distance...
Good day,
I tried to build the standard Nordic application: Blinky for the nrf52840dk/nrf52840 board from the following directory on my PC: c:\ncs\v2.9.1\zephyr\samples...
Hi,
I'm developing custom firmware on the appcore and netcore. The netcore runs BLE controller, as well another custom IPC service to communicate between the appcore and...
Hi,
we are looking into incorporating a NRF52 module into our control units, but to allow extending the antenna position away from the case through male-female SMA cables...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
Hello Everyone,
I try to develop Nuvoton + NRF24L01 SPI communicate each other. And I don't understand why MISO bus has 0x0E after I send Write_Command 0x20?
void NRF24_AdressTX...
On the nRF54L15, how can I update the maximum TX time to 17040 µs when using Coded PHY?
I'm currently testing with the Throughput sample in nRF Connect SDK v2.9.1. During...
I have successfully tested the SPI master loopback example on pca10001 eval board. I have a few questions regarding a real-world scenario when there is a slave SPI present...
I'm trying to follow the instructions for "nRF51822 Beacon Firmware Documentation" for over the air firmware upgrade of the smart beacon, but I can't find the soft device...
Could this be my problem?
devzone.nordicsemi.com/.../s110-7-0-0-can-i-write-my-own-mbr
an application now starts at 0x15000 which is to make room for an extra 4Kbytes...
Hi,
I am new to BLE Development. Currently I am using NORDIC Development board (SDK Ver 5.2 &Soft device S110). I want to write a small program to establish the connection...
I'm trying to get a handle on the various ways I can implement console output on this system.
I have in the past used the retarget.c/.h code from this forum that uses simple_uart...
Hi
I use the random number generator of LE1,I have made a demo code and the code can generate a random number.As the project in attachment.
I want to get a random time...
Hi all
I get LE1 enter sleep mode(PWRDWN = 0x04;)and use RTC to wake up,but LE1 cann't enter interrupt function after RTC wake up.
If I just use RTC to run ,LE1 can...
Hi,
I am using a custom board with nRF51822 to transmit data. Everything works fine except the transmitting always stop after a while. I am using softdevice 5.2.1. I attach...
Hi,
i want to start timer 2 and read its value just before the radio gets active. I've seen in the nr51 series reference manual i can use task capture to set the current...
I am developing using a nrf51822.I need delay timer
that can be substitued for nrf_delay_ms().
in other words,need a task delay that can be taken some event from another...
Hi,
i'm reading through a document that is part of the ble-sdk-arduino
The document is titled "HID over GATT maps USB HID to the bluetooth Generic Attribute profile...
Hi,
I have 2 timers and APP_TIMER_MAX_TIMERS = 3. I am getting NRF_ERROR_NO_MEM error.
If I increase to 6 it works. Is it 3 APP_TIMER_MAX_TIMERS per timer?
Thanks...
Hello,
I am running a nRF51822 rev G0 with Soft Device 6.0.0 & SDK 5.2.0. My device implements a custom service with 4 characteristics. One of those characteristics is...
HI,all!
In the funtion on_ble_evt(), there is one of the events named "BLE_GAP_EVT_TIMEOUT", can someone please tell me what situasions might cause this event? (be better...
