I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello everyone!
I'm currently developing a project in which I require a remote control (touchscreen TFT + arm MCU) to send and recive some data over a bluetooth connection...
Hallo
We want to update the firmware over the air (BLE).
What is a safty concept?
Our firmware need about 60KB flash ROM.
What have we to calculate for BLE software?
...
Hello Everybody,
I have a question about nRF51422. I want to monitor the ANT+ message from any sensor, which is already connected with the device,
Scenario : if it is...
Hello,
Im trying to create a synchronisation method for sensors using BLE. At the moment i can synchronise them within 10ms accuracy, in theory it should be within 2ms...
Dear all:
same as this issue:
devzone.nordicsemi.com/.../use-dfu-to-update-ap-over-ble-single-bank
it seem same as my way that modify modify "dfu_dual_bank_ble" target...
A big update this week for our S110 SoftDevice. Full OTA DFU for SoftDevice and Application. Also Multi-acivity concurrency for Bluetooth Smart and 2.4GHz protocols. As Developers...
Hello
I got my nRF51422 DK, and got few inquiries
For ANT,BLE DK, where can i find API documentation?
BLE can be implement on nRF51422 DK?
Is there sample project...
I have a 'fresh' nRF51822 on a board and it's not clear to me what procedure I need to follow in order to get it to work. I'm using the Segger programmer and I can program...
In the Keil debug interface, how can I find if the application is throwing an ASSERT, and which it is? I'm using the S110 softdevice. (See other question for context devzone...
Hello, I have a weird problem, the nRF24L01+ is sending a TX PAYLOAD that was left in the TX FIFO (clocked with W_TX_PAYLOAD) as an ACK PAYLOAD when switching to PRX mode...
hello everyone,
i am trying to use SDA and SCL pins of TWI other than 24 and 25, is it possible? i want to know before using other pins for twi other than 24 nd 25 with...
Hi
I try to communicate with others TWi devices using the twi_hw_master driver.
When i initiate a communication with twi_master_transfer , i don't receive any ack from...
Hi,
I have purchased the nRF8001 Development Kit and so far I wired the nRF2740 board to a FTDI VNC2 microcontroller. I have been reading about how to configure the 8001...
Hello. I'm trying to port the ble_hrs to a custom board with an NRF51822 on it, but the advertising never starts. While I'm debugging this, what should I be looking out for...
