Hi Team,
we are using two nRF5340 Audio DK kits to test LE Audio CIS example (unicast client & server).
kit1 nRF5340 Audio DK - act as gateway ( connected to PC/shared...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Hello, My SDK is NCS2.8.0, I want to know the version of matter, but I can't find it, may I know how to get?
BTW, does NCS SDK support Matter 1.4.0, if yes, could you tell...
Hi sir
If nRF51822 unexpectedly enter DFU OTA mode, did boot loader have timeout counting to exit DFU?
Besides, if nRF51822 entered DFU mode and didn't update new firmware...
Hi all,
This 60-second limit is not enough for us. Our application is 48 kB & takes 35 seconds to upload. It should be enough, but the problem is that our iOs app does...
Hi All,
I use S120 device to monitor advertising and output the mac address,RSSI information via UART to PC terminal. The PC terminal can receive data continusly from the...
I found ble_dfu.py referenced in some posts to help automate the generation of an application.dat metadata file used (along with the application.hex file) to create the input...
in the code below, the keil IDE is flagging with red squiggly APP_BUTTON_INIT, claiming that it is an undefined symbol. It also says that this implicit declaration of 'APP_BUTTON_INIT...
Hello all.
while trying to calculate the data rate from bluetooth low energy , i have two questions
Is there a possibility to measure the data rate by using nrf sniffer...
I have an algorithm which does quite a bit of number crunching. I'd like to know how many clock or instruction cycles this algorithm is using. How can I get or calculate the...
Hi all,
I am not sure what to do now. I have been trying to get the s130 working with the device manager. I tried using github.com/.../nRF51-ble-app-hrs-s130 with sdks...
Hello,
in my application i use a bootloader for S310 and S310 V2.1.0.
The Bootloader is configured to use NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION and the application...
Hello Everyone
I am using two application timers one of standard battery service and one i have made for adc sampling like this along with the code added for battery timers...
When I update the advertising data from the radio pre activation hook (800µs), the updated data does not appear in the advertising event following 800 µs after the hook is...
Custom Board with MCU NordicSemi nRF51822-QFAA
Softdevice S110 7.1
IAR for ARM 7.1
SDK 7.2 using a merged service (HID keyboard example + NUS example...
As per the steps given to program bootloader to the device i have programed it.
But the code is not getting executed i.e advertising nor led initilization is taking place...
Hello im trying to connect to a slave on BLE_GAP_EVT_DISCONNECTED event.
Can i use sd_ble_gap_connect(...) on this state, im getting error code 0x3202.?
regards, Vo...
Hi, I have bought the nRF51 development kit. I have downloaded source code for nRF51822. This comes with LOTS of examples but I suspect the codes are not for my board. Is...
