I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
Hi, sorry if this is a dumb question. I've just ordered some development kits and maybe that will answer the question, but i'm being a bit impatient!
I want to put an nrf51422...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi all,
In my project ,I use the SPI to communication between nRF51822 and STM32,but I don't know
how does the heart_rate data transmit to BLE stack.
I am confused...
We have a custom nrf15822-AA board flashed with the S110 (6.0.0) and our application. It has a 32khz crystal. It is connect to our (Mac) development systems with a SEGGER...
I use 51422 with ANT function. When I set a command like "sd_ant_channel_unassign", how can I get response from on_ant_evt callback?
I need to do something after ANT unassign...
I have a nRF8002, I use nRFgo Studio to program the board, and Master Control Panel on Windows to check it board values.
I would like to be able to recognize when the nRF8002...
As the network speed is so low that I often cann't access www.nordicsemi.com, especially on weekends.
Could you tell me the reason?
Note:
At the time when I can...
I am successfully communicating through nrf 8001 chip and i using this module. Now i want to write services and characteristic to this module through iPhone after getting...
Hello：
1.
I used connect Master Control Panel and ble_app_cscs services see the following received some data not understand do not understand, here's UUID I did not see...
Hi all,
I have various questions regarding the softdevices, memory management and power consumption of the nrf51822 chips.
The project we are working on will need to...
I am working on nRF24LE1 boards. I am trying to talk between two boards. I have loaded "enhanced_shockburst_ptx_nrf24le1" and "enhanced_shockburst_prx_nrf24le1" on two different...
I saw an ANCS examples in sdk5.1.0(softdevice=6.0.0), and then I put this example to port to sdk4.4.2 (softdevice=5.2.1) and the example worked perfectly. But when I put the...
Hello,
I have set up my project to use the DFU bootloader to upgrade the application. When my application is running it can be sent a command from the central device to...
Hi
Can I read the content of RF register for LE1 by using the SPI of extern MCU?No matter the code of LE1 is encrypted or not.
When set the LE1 to 0dBm,the TX power...
[*] Hi Guys, Newbee for Nordic, so sorry if its a silly question. I have a nRF51422 and all demos are working great.
But, I need to develop Windows 8 app using the supplied...
