I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
During the pairing phase, LTK will be generated for the secure connect, and no LTK will be generated for the legacy pair, but LTK will be generated for the subsequent bonding...
Where can I find documentation of http://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.2.0/nrf/samples/nrf9160/serial_lte_modem/README.html#serial-lte-modem IP UDP low power...
Hi, I am trying to create a custom_service for my application.
I am using nRF52832 SDK_16
SES
I want to create the BLE_SERVICES
which has send characteristics and...
Hi,
I converted ble_app_beacon example to Segger Embedded Studio (using version 4.30b), as per the instructions in the link https://infocenter.nordicsemi.com/index.jsp?topic...
I configured a NRF52832 with non-scannable and non-connectable as well as scannable/connectable advertising. Everything is working fine.
But I want to fully understand the...
I have an existing phone app (using the traditional GATT system), and I would like mesh-enable my products so that if the products can see each other, then the phone can connect...
nRF51822 PS says standard drive GPIO output voltage will be VDD-0.3V ~ VDD In our previous project w/ nRF51822, I found it to be very close to VDD when connected to GND via...
Hi... i am using nRF52832 ,15.2 version sdk . I want to send the data from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can able to transmit the...
Hello,
I'm trying to setup an automated pairing for two devices. My peripheral device is advertising and should only allow connection requests from a specific central device...
I'm developing a multirole device to connect to a peripheral device that we developed earlier.
The multirole device when acting as a central device it scans for the peripheral...
To the kind attention of Nordic support team,
1. I have been using secured gazell library, where master is always polling in order to receive a message.
I was wondering...
Hi!
I'm developing a TCP server running on th e nRF9160, but there seem to be a problem with accepting clients. The code is very simple, just calls to socket, bind, listen...
Hi. I've developed a PCB with nRF52832 and I'm having problems with the circuit. When I put my hands closelly of P0.00(XL1) and P0.01(XL2) the bahavior of nRF changes... I...
I apologize if this was already answered elsewhere - I didn't find it.
I have been digging in the nRF52840 source code for the serial_nRF52840 SES project to understand...
