Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
<Environment> - Windows10 - nrf v1.3.0 - modem fw 1.2.0
I'm attempting to make a socket and communicate with the modem using it.
However, sending data doesn't work out...
Hi everyone,
Looking the nRF52840 Product Specification v1.1, I see that there are several System Off modes.
1. Using the function sd_power_system_off() what is the by...
Hi,
i'm new on using nRF5 modules and i have some question about how to program the nRF52840 on a custom board, so with a completely new chip.
Reading the schematic of...
I am using nrf52840 DK (pca10056) board and nrf5SDK 16. There is one low power sensor connected to the board via SPI interface. My program consume less than 30uA before I...
HI:
I transfer the init packet and firmware to bootloader successfully by UART DFU, and then the app can not start. It report error as below:
<00> info> app: Inside main...
Hi All,
My update of nRF Connect v3.3.0 failed after a while:
Update of nRF Connect failed with the following Error-MSG:
On the same day I got an install from Oracle...
Hello everyone,
I would like to use the PPK with a NRF52 Dk, but I have external sensors connected to the VDD and 5V, so when I will plug the ppk I will have to disconnect...
Hi,
I am reading a 24-bit data from SPI by getting a data-ready interrupt from GPIOTE pin in a NRF52832 chip. I have to buffer data for the BLE interval duration then send...
Hi,
I am using BLE-UART example in my project and to start advertising I am using below piece of code.
By default in the sdk (ble_advertising.c) the advertising type...
Hi,
I don't want the spm and application firmware built together so I tried using the "spm" sample in version 1.3 of the sdk. However when configuring the project i t...
I have a requirement that my peripheral device should only rely on the central to start any security operation. Right now I see a problem when the central side removes the...
I am new to BLE with my nRF51. I've got this example and I try to stop a RSSI scan when the device get all advertising data from the local device.
But when I try to add...
I burned this program in nrf9160 ncs v1.3, and how do I fix the following error?
An example can be found in the figure below
Example prj configuration see figure ...
Hi,
I would like to evaluate the NRF52811 chipset module (BMD-360 from UBlox) using the NRF52840 DK.
If I am to read the Constant Tone Extension that will be transmitted...
I followed an instructions developer.nordicsemi.com/.../gs_assistant.html in the case of Kubuntu 20.04 and developer.nordicsemi.com/.../gs_assistant.html in the case of Windows...
