Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I have nRF52840 Dongle(PCA10059), I try to develop on the nRF Connect Desktop. But this dongle can't update firmware on the nRF connect desktop.
My operation below...
I’m using the latest version of the modem 1.2.0 and sdk v1.2.0
For the most part AWS FOTA seems to be functioning.
However it will start the FOTA job and hang and fail...
Hi everyone,
I need to set up a timer using the RTC. The default function that converts ms to ticks APP_TIMER_TICKS() accepts only milliseconds. So, I wrote my own conversion...
I want to interface Client Sensor over UART in light_switch_client code. Can you please give me the idea,how to do it.
I am using Mesh_V4.0 and SDK 16.0
Hi, teams.
I am trying to implement DFU functionality on mesh node devices.
Currently, I am using Mesh SDK 4.1.0 and have read DFU-related documents, but still something...
Hello -
We are working with a custom board that is similar to the SparkFun Pro nRF52840 Mini . We are using the nRF52840 SDK version 16.0.0 and SoftDevice 6.1.1. Our board...
Hi everyone.
I am working on the ble_app_bps_pca10056_s140 example. I want to confirm that a BLE event is received when the APP_ADV_DURATION has been expired.
After searching...
Hi,
I noted that the CW generated in the %XRFTEST TX test seems to be offset from the requested frequency. Specifically, issuing the command
AT%XRFTEST=1,1,20,8500,-50...
Is there still no way on this build to setup zerocrossing detection?, I mean using interrupts I developed a zigbee dimmer that detects zero crossing and dims 3 separate channels...
Hi,
We are using NRF52840 Dk board to transfer the data at 10ms through Bluetooth which is central and peripheral as other cc250moda controller Bluetooth. Our objective...
Hello:
I am porting the LESC with MITM security protocol from your "ble_app_multirole_lesc" example inyo a project that runs FreeRTOS. This is on an NRF32540 With s140...
Hi,
I'm using an nrf52840 dk to query another device over spi and then pipe the response back USB to a host PC. Ideally, we're piping data at 1 Mbps (which should be very...
Hi,
We are using nRF9160 DK. Loaded the asset tracking application, and followed all the procedure to connect to nRF cloud.
In nRF cloud i can see the data in the cloud...
Hello,
I am currently designing a custom PCB with the nRF8001 chip. For a smoother assembly and component procurement, I am looking to make all the resistors on the board...
