Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I have built my code on top of ble_app_template and im using a custom service. My problem occurs when sending data from an android Samsung S9 (and possibly other android...
Hi,
we have designed the nrf52840 custom board.The programming is working correctly in the custom board using the gnd detect,vtg swdio, swd clk pins.Here the problem is...
Hi,
Is the Errata 15 applicable to Softdevice?
Does Softdevice at any point read the RAM state using RAM[x].POWERSET and RAM[x].POWERCLR registers?
Thanks,
Just...
Hi Now I'm developing using nRF52832, and trying to estimate programming time.
So, I want to know what time to wrie one word "tWRITE" mean exactly. Does it mean that one...
Hello, I am currently building a wireless sensor network, and I am searching for a transceiver and not a complete system on chip. I was working using NRF24L01, and now is...
I tried to write in flash since a couple of weeks.. and i am not able to do it... I am using SoftDevice... so i think i have to use Persistent Storage Manager Where can i...
Hi Devzone:
I am using the example project "fsorage" on nRF52840.
I see the project specifies the range for the flash storage to be
.start_addr = 0x3e000, .end_addr...
Hello
I am preparing for Bluetooth SIG certification. I use nRF52810 / SDK15.0.0 / S112 6.0.0.
I've been helped by Nordic about QDID before.
https://devzone.nordicsemi...
Hi there
After initializing the SoftDevice S132 V6.1.0, I request the HF crystal by calling the function sd_clock_hfclk_request():
Later in the code, after a BLE connection...
SDK:V16.0.0
chip:52832
development kit:window+keil
I trying to combine libuarte and ble_central\ble_app_multilink_central\. My project work well in ble_central. But...
Hello everyone, I need to build a photo capture application.
And the CMOS sensor go through MIPI-CSI2 interface.
Is there any example code and library for nRF5340?
Hi,
How should the USB pins be handled in case I don´t want to use them? Should they be just left unconnected?
What about VBUS pin?
Thanks and regards,
Juan
Hello,
I got the issue to run the NRF9160 DK as an external AT-Modem. What I need to do is to issue AT-Commands over the UART, which control the NRF9160 modem through an...
