Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi,
How do I measure the length of the created advertisement buffer? I want to add two UUIDs in the packet and the device is resetting. I guess the length is the issue...
Hi,
Is there any kind of dependency tree for the libraries and drivers of the SDK (NRF5)?
I have been searching the Infocenter documentation but I haven't found anything...
Hi,
I am using the TWI scanner example from the sdk15. Board is NRF52840. I have a differential pressure sensor connected to the TWI input pins on the nordic board and am...
Hello!
Trying to capture and print the rssi values for all simultaneous connections from the multi_central example. I'm using an nrf52840 SoC that will be connected to four...
Hello, I am looking to use the thingy 52 as a remote sound recording device using BLE connection. I also have downloaded the source code for the thingy app and my question...
i want the ble_app_uart.c example to advertise also . so here i want to merge the ble_app_uart central +peripheral uart right ?
what are the changes i need to do
...
Hi Sir,
According to the datasheet of 52840 (v1.1), in the ref. schematic, the requirement of 32M is +/- 40 ppm.
In section 5.4.4.2, for the frequency tolerance requirement...
Hello,
Please comment on the expected difference in achievable range using 20 dBm vs. 23 dBm output power. Any details, assumptions, questions, etc. would be appreciated...
Hi, I'm looking for a more modern transceiver than nRF24L01 + and that works for the same. I am looking for a low or ultra low power transceiver that allows the implementation...
Hi, For my POC I use nrf9160 dk. Nrf52840 is used for scanning ble devices and nrf9160 dk is used for sending data to mqtt server (very similiar to one of the examples with...
Hello there!
We would like to use INT1 pin of ADX362 low power accelerometer on Thingy:91 board to interrupt nRF9160 (e.g. wake it up) when some motion is detected.
To...
Hello,
I am currently designing a new board using the nRF9160 chip and looking for an alternative component to use instead of the GPS RF Amplifier QM14501 and RF Switch...
I need to exchange data between nrf52840 and Linux PC. I see example project in nrf5SDK/examples/peripheral/usbd
Can anybody advise any example project for Linux C/C++ to...
Hi,
I'm working on nrf52840. As far as I understand, that device supports connection to peers with BLE 4.2 at least.
However, I'm able to connect via my phone, which...
Hi,
I have some questions regarding the state of the GPS functionality, and the future plans for nrf9160.
Will continuous GPS tracking while simultaneously using LTE...
