Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
This is not a question. But it may save you sometime. :-)
Remember to zero this variable before call fds_record_find.
fds_find_token_t ftok;
Actually it is mentioned...
Dear Community,
I am working on a project where the idea is to build a board that can measure the resistance over a small biosensor. The biosensor will be connected between...
nRFConnect for Desktop v3.3.0 App: Bluetooth Low Energy v2.3.2 Windows 10 x64 ( 19.04, 19.09), using Dual Monitor. Device: PCA10059 or PCA10056
I can start, connect, and...
In the "Cellular IoT development on Nordic Thingy:91" video (-> https://webinars.nordicsemi.com/cellular-iot-development-on-nordic ) an nRF Connect SDK Toolchain manager app...
SDK14+Nrf52832:
I want use one pin as a interrupt pin.
when the pin level from high to low, execute A task;
while when the pin level is from low to high, execute B task...
Hi Folks,
Windows 10, clean install of ncs v1.2.0, using nRF5340-PDK with SES 4.42a. Project blinky rebuilds and runs fine. Now I need a zephyr example of creating a simple...
Hi,
What is the suggested way to switch between 64MHz and 128MHz on the application core? Normally I want to run at 64MHz, but sometimes boost it to 128MHz. Is there additional...
Hi,i use the bootloader demo code , the file path is nRF5_SDK_16.0.0_98a08e2\examples\dfu\secure_bootloader\pca10056_s140_ble\arm5_no_packs ,a fter I compiled and passed,...
Hi,
I know this question has been asked a million times before, but most of the links are now dead, and the advice seems stale. On sdk 15 and up, how do I go about setting...
Working on a BLE application on a nRF52833 development board with FreeRTOS (external/freertos), and I noticed that the SDK uses dynamic allocation for FreeRTOS, e.g., xTaskCreate...
Hi community, I need some help with mesh programming cause i'm new to it ! First, i'll explain what i've done : I create a program on visual studio, which can communicate...
Hi,
I am starting a new iOS BTLE project for a new kind of music instrument. I started with the Thingy believing that that would be a good reference design to start from...
Hi!
Working on project based on nRF52810. Everything was fine until I began to work on part to save setting in flash memory.
I've used flash_fds example SDK 16.0 as starting...
Hi,
Currently I’m working on a device which is, on the one side connected to a smartphone via BLE and on the other side to another uC via UART.
Therefore, the UART speed...
