Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hello,
I am working on nRF52382 IC. I am accessing GPIO also. But still i don't get the access of antenna. I have make the circuit as per the development board of nRF52...
Hi,
What is the practical maximum throughput of nRF proprietary protocol? The following table showing ESB and GAZEL has 1.3Mbps and 128kbps respectively.
https://www.nordicsemi...
Hello,
I am developing application based on nRF52833 DK. Basically, my application scans all iBeacon messages (ADV_NONCONNETABLE) and transmit to computer.
I would like...
Dear All,
I need your help because I created a PCB with the nrf52840 and a flash connected exactly as the one on the dev-board.
The only difference is that the one on...
I am using nrf52840 . I am sending data 2 bytes as FF .I put the data in 2d array like this. char dataSend[1][5]={"FF"}; This char dataSend has 1 row and 5 length .This should...
I need transfer data to/from NRF52840.
I see I can do it by using function nrfx_usbd_ep_transfer - but don't see any examples.
I want to make bulk endpoint and be capable...
Hi,
I am running ble_app_blinky example on nRF5280 custom board, it is giving me Error 133 (0x85): GATT ERROR . Since I have nrf52DK, I tried same example with SD 132 on...
Hello,
i am using the NRF52832 and the NRF52840 with different softdevices. Now I want to update the softdevices over the air and I need the SD Version strings of all the...
A bit more detailed: A bug has been detected on the device under development. It is connected with the fact that if you try to disconnect a connected device on an iMAC Catalina...
Hi
I am trying to install the SES toolchain on my PC (Win 8.1) following exactly the nRF Connect v3.2.0 Getting Started Assistant. When trying to "Open nRF Connect Project...
I am using a nRF52 DK to program an externally powered board with a NRF52811.
I am able to flash a blinky program onto the custom board successfully using the output .hex...
Just as the title says, I'm trying to measure an input pulse width using PPI and GPIOTE. I am currently measuring the pulse width using timer interrupts, but I would like...
Good day!
generic_ponoff_setup_server_init causes Mesh assert error.
If I delete reallocation of dtt and onoff servers' subscription lists everything goes fine.
What...
Hi!
I have been using LoRa for communication for my product. I'm looking into using BLE mesh.
I have a couple of hundred sensors, all 1-2m apart from each other. Here...
In this scheme we use 2 inductor in a serial connection. 15 nH + 10 uH. Total inductor = 10.015 uH. ??? Is really need to add this 15 nH inductor? For why? If we just short...
